參數資料
型號： MT90221
廠商： Mitel Networks Corporation
英文描述： Quad IMA/UNI PHY Device(四端口 IMA/UNI 物理層設備（四端口ATM IMA和UNI處理器）)
中文描述： 四IMA的/單向物理層設備（IMA的四端口/單向物理層設備（四端口自動柜員機IMA的和單向處理器））
文件頁數： 22/116頁
文件大?。?/td> 309K
代理商： MT90221
MT90221
14
The SCCI field is incremented by one for each
transfer command performed which includes a
change in at least one byte of the ICP cell.
2.4.8
An optional interrupt is provided at the end of an IMA
frame to simplify software implemented changes in
the Group Control and Status field. This interrupt can
be enabled on an as required and per group basis to
implement a frame counter. The
TX ICP Cell
Handler
and
TX ICP Interrupt Enable
registers are
used for the transfer ready and frame interrupt.
IMA Frame Programmable Interrupt
2.4.9
The content of the Filler cell is pre-initialized and
conforms with the IMA Specification.
Filler Cell Definition
2.4.10 TX IMA Group Start-Up
Initialize the TX IMA Group start-up as follows:
(Note: The startup procedure below is given
indicating the most important steps. A more detailed
and complete sequence can be found in the
MT90220/221 Programmer’s Manual and example
code)
Configure the TX PCM port(s) by writing to the
TX PCM Link Control
register 1 and 2.
Write the value of M, the Timing Mode and the
reference link number to the
TX Group Control
register corresponding to the IMA Group
number to be initialized.
Write the Link ID (LID is between 0-31) to
TX
Link ID
registers for each link to be used in the
IMA Group. LID should not be changed when a
group is operational. Ensure each link that is
part of an IMA group has a unique LID (note
that the MT90221 does not verify LIDs).
Write the ICP Cell Offset value to
TX ICP Cell
Offset
registers. This value depends on the
value of M. Typically, the reference link will have
a delay of 0 cells in the IMA Frame and the ICP
cell in each other link will be evenly spaced in a
multiple of M/N cells (where M is defined in the
IMA specification and N is the number of links).
The offset value for an operational group should
not be changed.
Write to the
TX Link Control
registers to put
the link(s) in IMA mode and to enable the
transfer of ATM User Cells when required.
2.4.11 TX Link Addition
The MT90221 supports software controlled link
addition to the existing IMA group. Link addition is
used to increase the available bandwidth. The
TX
PCM Link Control register 1
and
2, the TX Link ID
and
TX ICP Cell Offset
registers are initialized first
with the proper IMA Group information. The link is
assigned to a TX IMA group by writing to the lower 2
bits of the
TX Link Control
register. The bit 3, 1 and
0 of the Test 2 register have to be written with the
proper value. The link is then configured in IMA
mode by writing to the bit 2 of the
TX Link Control
register. The
TX IMA Mode Status
register is
monitored to detect when the link is reported in IMA
mode. When the link is in IMA mode, then the bit 3, 1
and 0 of the
Test 2
register are reset to 0.
TX Link
Control
register bit 6 determines when ATM User
cells can be sent. Note that the
Test 2
register
cannot be used as a read/modify/write register. The
values that are written and the values that are read
are independant. Note also that the bit 6 of the
Test
2
register shulld always be set to 1.
2.4.12 TX Link Deletion
There are two reasons to remove a link: the required
bandwidth decreases or a link becomes faulty. The
MT90221 supports link deactivation under software
control.
A link stops transmitting User cells when bit 6 of the
TX Link Control
register is set to 0. Filler and ICP
cells will still be sent on the link. The link is removed
from an IMA group by first setting the bit 2 of the TX
Link Control register to 1 while keeping the original
IMA group number. The IMA group number can be
changed only when the link is reported in UNI mode
as reported in the TX IMA Mode Status register. It
then can be assigned to another IMA group.
When removing the last link of a TX IMA group, the
TX Utopia FIFO has to be empty. This can easily be
done by first disabling the source of ATM cells (ATM
Utopia contoller), then disabling the TX Utopia Port
using the UTOPIA Input Link or Group PHY Enable
registers while still keeping the “Send User Cell” bit
of the TX Link Control register set to 1. After a period
of time corresponding to “n” IDCR clock tick has
elapsed, then the above procedure can be applied to
assign the link in UNI mode.” The value of “n”
depends on the size of the TX Utopia FIFO as
defined in the TX FIFO Length Definition registers.
The level of the TX Utopia FIFO can be monitored
using TX Utopia FIFO Level register. Then, the
above procedure can be applied to assign the link in
UNI mode.
2.5
A maximum of four independent T1/E1 interfaces
can be selected in UNI mode. Figure 4 gives a
functional block diagram of the transmitter in UNI
mode.
ATM Transmit Path in UNI Mode
相關PDF資料
PDF描述
MT90401 SONET/SDH System Synchronizer(SONET/SDH 系統同步裝置（由一個數字鎖相環組成）)
MT9040 T1/E1 Synchronizer(T1/E1 系統同步裝置（由一個數字鎖相環組成）)
MT9041A ()
MT9041B T1/E1 System Synchronizer(T1/E1系統同步裝置（由一個數字鎖相環組成）)
MT9042B ()
相關代理商/技術參數
參數描述
MT90221AL 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Quad IMA/UNI PHY Device
MT90222 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:4/8/16 Port IMA/TC PHY Device
MT90222AG 制造商:Microsemi Corporation 功能描述:ATM IMA 40MBPS 2.5V 384BGA - Trays
MT90222AG2 制造商:Microsemi Corporation 功能描述:ATM IMA 40MBPS 2.5V 384BGA /BAKE/DRYPACK - Trays
MT90223AG 制造商:Microsemi Corporation 功能描述:ATM IMA 80MBPS 2.5V 384BGA - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*