- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9076AB (Mitel Networks Corporation) T1/E1/J1 3.3V Single Chip Transceiver PDF資料下載
參數資料
| 型號： | MT9076AB |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/J1 3.3V Single Chip Transceiver |
| 中文描述： | T1/E1/J1收發3.3V的單芯片收發器 |
| 文件頁數： | 137/160頁 |
| 文件大?。?/td> | 416K |
| 代理商： | MT9076AB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁當前第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
Preliminary Information
MT9076
133
Bit
Name
Functional Description
7-0
TxCNT7-0
Low Transmit Byte Count Register.
This register, along with the Extended
Transmit Byte Count Register indicates the length of the packet about to be
transmitted. For a packet size of 255 or less it is only necessary to write this
register. When this register reaches the count of one, the next write to the Tx FIFO
will be tagged as an end of packet byte. The counter decrements at the end of the
write to the Tx FIFO. If the Cycle bit of Control Register 2 is set high, the counter will
cycle through the programmed value continuously.
Table 168 - Low Transmit Byte Count Register
(Page B,C & D, Address 1AH)
Bit
Name
Functional Description
7
HRST
HDLC Reset.
When this bit is set to one, the HDLC will be reset. This is similar to
RESET being applied, the only difference being that this bit will not be reset. This bit
can only be reset by writing a zero twice to this location or applying RESET.
6
RTLOOP
RT Loopback.
When this bit is high, receive to transmit HDLC loopback will be
activated. Receive data, including end of packet indication, but not including flags or
CRC, will be written to the TX FIFO as well as the RX FIFO. When the transmitter is
enabled, this data will be transmitted as though written by the microprocessor. Both
good and bad packets will be looped back. Receive to transmit loopback may also
be accomplished by reading the RX FIFO using the microprocessor and writing
these bytes, with appropriate tags, into the TX FIFO.
5
- -
Reserved
. Must be set to 0 for normal operation.
4
- -
Reserved
. Must be set to 0 for normal operation.
3
CRCTST
CRC Remainder Test.
This bit allows direct access to the CRC Comparison
Register in the receiver through the serial interface. After testing is enabled, serial
data is clocked in until the data aligns with the internal comparison (16 RXC clock
cycles) and then the clock is stopped. The expected pattern is F0B8 hex. Each bit
of the CRC can be corrupted to allow more efficient testing.
2
FTST
FIFO Test.
This bit allows the writing to the RX FIFO and reading of the TX FIFO
through the microprocessor to allow more efficient testing of the FIFO status/
interrupt functionality. This is done by making a TX FIFO write become a RX FIFO
write and a RX FIFO read become a TX FIFO read. In addition, EOP/FA and RQ8/
RQ9 are re-defined to be accessible (i.e. RX write causes EOP/FA to go to RX fifo
input; TX read looks at output of TX fifo through RQ8/RQ9 bits).
1
ARTST
Address Recognition Test.
This bit allows direct access to the Address
Recognition Registers in the receiver through the serial interface to allow more
efficient testing. After address testing is enabled, serial data is clocked in until the
data aligns with the internal address comparison (16 RXc clock cycles) and then
clock is stopped.
0
HLOOP
TR Loopback.
When high, transmit to receive HDLC loopback will be activated.
The packetized transmit data will be looped back to the receive input. RXEN and
TXEN bits must also be enabled.
Table 169 - HDLC Test Control Register
(Page B,C & D, Address 1BH)
相關PDF資料 |
PDF描述 |
|---|---|
| MT9076 | T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) |
| MT9079 | Advanced Controller for E1(先進的E1幀調節器和控制器) |
| MT9080B | SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊) |
| MT90810 | Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路) |
| MT90812 | Integrated Digital Switch (IDX)(集成數字開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9076AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076B | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
| MT9076BB | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BB1 | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
發布緊急采購，3分鐘左右您將得到回復。