參數資料
型號： MT9076AB
廠商： Mitel Networks Corporation
英文描述： T1/E1/J1 3.3V Single Chip Transceiver
中文描述： T1/E1/J1收發3.3V的單芯片收發器
文件頁數： 94/160頁
文件大?。?/td> 416K
代理商： MT9076AB
MT9076
Preliminary Information
90
20.2
Per Time Slot Control Words (Pages 7 and 8) (T1)
The control functions described by Table 80 are repeated for each DS1 time slot. Page 7 addresses 10000 to
11111 correspond to DS1 time slot 1 to 16, while page 8 addresses 10000 to 10111 correspond to time slots
17 to 24. Table 83 illustrates the mapping between the addresses of these pages and the DS1 channel
numbers.
Page 7 Address:
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Equivalent DS1
channel
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Page 8 Address:
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Equivalent DS1
channel
17
18
19
20
21
22
23
24
x
x
x
x
x
x
x
x
Table 82 - Pages 7 and 8 Address Mapping to DS1 Channels
Bit
Name
Functional Description
7
TXMSG
Transmit Message Mode.
If high, the data contained in the Transmit Message Register
(address 18H, page 1) is transmitted in the corresponding DS1 time slot. If zero, the data on
DSTi is transmitted on the corresponding DS1 time slot.
6
PCI
Per Channel Inversion.
When set high the data for this channel sourced from DSTi is
inverted before being transmit onto the equivalent DS1 channel; the data received from the
incoming DS1 channel is inverted before it emerges from DSTo.
5
RTSL
Remote Time Slot Loopback.
If one, the corresponding DS1 receive time slot is looped to
the corresponding DS1 transmit time slot. This received time slot will also be present on
DSTo. If zero, the loopback is disabled.
4
LTSL
Local Time Slot Loopback.
If one, the corresponding transmit time slot is looped to the
corresponding receive time slot. This transmit time slot will also be present on the transmit
DS1 stream. If zero, this loopback is disabled.
3
TTST
Transmit Test.
If one, a test signal, either digital milliwatt (when control bit ADSEQ is one) or
PRBS (2
15
-1) (ADSEQ is zero), will be transmitted in the corresponding DS1 time slot. More
than one time slot may be activated at once. If zero, the test signal will not be connected to
the corresponding time slot.
2
RTST
Receive Test.
If one, the corresponding DSTo timeslot will be used for testing. If control bit
ADEQ is one, a digital milliwatt will be transmitted in the corresponding DSTo channel. If
control bit ADSEQ is zero, the receive channel will be connected to the PRBS detector (2
15
-
1).
1
RPSIG
Serial Signaling Enable.
If set low, the transmit signaling buffer for the equivalent DS1
channel will be sourced from the ST-BUS channel on CSTi associated with it. If set high the
transmit signaling RAM must be programmed via the microport.
0
CC
Clear Channel.
When set high no robbed bit signaling is inserted in the equivalent transmit
DS1 channel. When set low robbed bit signaling is included in every 6th channel.
Table 83 - Per Time Slot Control Words (Pages 7 and 8) (T1)
相關PDF資料
PDF描述
MT9076 T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器)
MT9079 Advanced Controller for E1(先進的E1幀調節器和控制器)
MT9080B SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊)
MT90810 Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路)
MT90812 Integrated Digital Switch (IDX)(集成數字開關)
相關代理商/技術參數
參數描述
MT9076AP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver
MT9076B 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver
MT9076BB 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
MT9076BB1 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
MT9076BP 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*