- 您現在的位置：買賣IC網 > PDF目錄368145 > PSD301L Field Programmable Microcontroller Peripherals(可編程邏輯,16K位SRAM,19個可編程I/O,通用PLD有12個輸入) PDF資料下載
參數資料
| 型號： | PSD301L |
| 英文描述： | Field Programmable Microcontroller Peripherals(可編程邏輯,16K位SRAM,19個可編程I/O,通用PLD有12個輸入) |
| 中文描述： | 現場可編程微控制器外圍設備（可編程邏輯，16K的位的SRAM，19余個可編程輸入/輸出，通用PLD的有12個輸入） |
| 文件頁數： | 17/23頁 |
| 文件大?。?/td> | 118K |
| 代理商： | PSD301L |
Flash Memory – Application Note 048
3-35
*********************************************************************************************
W S I - PSDsoft Version 2.12
PSDabel Design Entry File
*********************************************************************************************
module flash411A1
title ‘WSI PSD4XX/5XX design for External Flash’;
“PIN DECLARATIONS
“Declare all the pins that are used in the PSD4XX/5XX.
“********************* Bus Interface signals declaration *********************
“The following are multiplexed latched address inputs that are available as inputs
“to the ZPLD.
a9,a8,a1,a0
a15,a14,a13,a12,a11,a10
pin 67,68,8,9;
pin 61,62,63,64,65,66;
“The following are bus control input signals from the 80C31
“In PSDConfiguration, you need to select:8-bit data, mux bus, and
“rd, wr, psen signal with active high ale.
rd
wr
psen
ale
reset
csi
clkin
pin 41;
pin 29;
pin 38;
pin 37;
pin 40;
pin 39;
pin 42;
“read line
“write line
“program space enable
“address latch enable
“reset input, active low
“PSD chip select, grounded if pin is not used
“clock input, optional
“**************************** Port A, B, C, D, E pin declaration ****************************
“The following are I/O Port pin assignments. Port functions that need
“to be declared here are:
“
1. latched address output a0-a7 (Port C or D)
2. other address inputs: a2-a7 (Port A)
“
3. MCU inputs/outputs
“
4. GPLD inputs/outputs
“Your software needs to set up the appropriate registers to enable Port functions such as
“the latched address and MCU I/O (see I/O section in the PSD Data Book for instructions).
“No equations are required if the pins are declared for non-GPLD function.
“If GPLD output is an internal feedback, you can assign it as a ‘node’, where the node
“number is the same as the pin number.
“For PLD pins: you may want the PSD Fitter to assign the pins for you for complex logic
“functions. In that case you need only to declare the PLD signal as ‘pin’ and omit
“the pin number.
Appendix B
相關PDF資料 |
PDF描述 |
|---|---|
| PSD302R | Field Programmable Microcontroller Peripherals(可編程邏輯,無SRAM,19個可編程I/O,通用PLD有16個輸入) |
| PSD303L | Field Programmable Microcontroller Peripherals(可編程邏輯,16K位SRAM,19個可編程I/O,通用PLD有16個輸入) |
| PSD303 | Field Programmable Microcontroller Peripherals(可編程邏輯,16K位SRAM,19個可編程I/O,通用PLD有16個輸入) |
| PSD311L | Field Programmable Microcontroller Peripherals(可編程邏輯,16K位SRAM,19個可編程I/O,通用PLD有12個輸入) |
| PSD311 | Field Programmable Microcontroller Peripherals(可編程邏輯,16K位SRAM,19個可編程I/O,通用PLD有12個輸入) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD301L-15J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD301L-15JI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD301L-15LI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD301L-15LM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD301L-15U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
發布緊急采購，3分鐘左右您將得到回復。