- 您現在的位置：買賣IC網 > PDF目錄192296 > S29CL016J0PFFM102 (SPANSION LLC) 512K X 32 FLASH 3.3V PROM, 54 ns, PBGA80 PDF資料下載
參數資料
| 型號： | S29CL016J0PFFM102 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 512K X 32 FLASH 3.3V PROM, 54 ns, PBGA80 |
| 封裝： | 13 X 11 MM, 1 MM PITCH, LEAD FREE, FORTIFIED, BGA-80 |
| 文件頁數： | 28/78頁 |
| 文件大?。?/td> | 1825K |
| 代理商： | S29CL016J0PFFM102 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
32
S29CD-J & S29CL-J Flash Family
S29CD-J_CL-J_00_B1 September27,2006
Prel imi n ary
After an erase-suspended program operation is complete, the bank returns to the erase-suspend
read mode. The system can determine the status of the program operation using the DQ7, DQ6,
and/or RY/BY# status bits, just as in the standard program operation.
To resume the sector erase operation, the system must write the Erase Resume command. The
bank address of the erase-suspended bank is required when writing this command. Further
writes of the Resume command are ignored. Another Erase Suspend command can be written
after the chip has resumed erasing.
The following are the allowable operations when Erase Suspend is issued under certain
conditions:
For the Busy Sectors, the host system may
Read status
Write the Erase Resume command
For the Non Busy Sectors, the system may
Read data
Program data or write the Suspend/Resume Erase command
8.7.5
Program Suspend/Program Resume Commands
The Program Suspend command allows the system to interrupt an embedded programming op-
eration so that data can read from any non-suspended sector. When the Program Suspend
command is written during a programming process, the device halts the programming operation
and updates the status bits.
After the programming operation has been suspended, the system can read array data from any
non-suspended sector. If a read is needed from the Secured Silicon Sector area, then user must
use the proper command sequences to enter and exit this region. The Sector Erase and Program
Resume Command is ignored if the Secured Silicon sector is enabled.
After the Program Resume command is written, the device reverts to programming. The system
can determine the status of the program operation using the DQ7, DQ6, and/or RY/BY# status
bits, just as in the standard program operation. See Write Operation Status on page 33 for more
information.
The system must write the Program Resume command in order to exit the Program Suspend
mode, and continue the programming operation. Further writes of the Program Resume com-
mand are ignored. Another Program Suspend command can be written after the device has
resumed programming.
The following are the allowable operations when Program Suspend is issued under certain
conditions:
For the Busy Sectors, the host system may write the Program Resume command
For the Non Busy Sectors, the system may read data
8.7.6
Accelerated Program and Erase Operations
Accelerated programming and erasing is enabled through the ACC function. This method is faster
than the standard program command sequences.
The device offers accelerated program/erase operations through the ACC pin. When the system
asserts VHH (12V) on the ACC pin, the device automatically enters the Unlock Bypass mode. The
system may then write the two-cycle Unlock Bypass program command sequence to do acceler-
ated programming. The device uses the higher voltage on the ACC pin to accelerate the
operation. Any sector that is being protected with the WP# pin is still protected during acceler-
ated program or Erase. Removing VHH from the ACC input, upon completion of the embedded
program or erase operation, returns the device to normal operation.
相關PDF資料 |
PDF描述 |
|---|---|
| S29CL016J1JFFM112 | 512K X 32 FLASH 3.3V PROM, 54 ns, PBGA80 |
| S29CD032J1JFAN110 | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
| S29CD032J1JFFN020 | 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80 |
| S29CL032J0RFAI113 | 1M X 32 FLASH 3.3V PROM, 48 ns, PBGA80 |
| S29CL032J0RFAN130 | 1M X 32 FLASH 3.3V PROM, 48 ns, PBGA80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29CL016J1JFAI020 | 制造商:Spansion 功能描述:16 - Tape and Reel |
| S29CL032J0MFAI030 | 制造商:Spansion 功能描述:32MBIT FLASH - Trays |
| S29CL032J0PQFM010 | 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:32MBIT FLASH - Tape and Reel |
| S29CL032J0RFAM010 | 制造商:Spansion 功能描述: |
| S29GL016A | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology |
發布緊急采購，3分鐘左右您將得到回復。