參數資料
型號： T7698
廠商： Lineage Power
英文描述： Quad T1/E1 Line Interface and Octal T1/E1 Monitor(四T1/E1線接口和八T1/E1監控器)
中文描述： 四T1/E1線路接口和八路的T1/E1監視器（四個T1/E1線接口和八T1/E1的監控器）
文件頁數： 39/112頁
文件大?。?/td> 1359K
代理商： T7698
Data Sheet
January 1999
T7698 Quad T1/E1 Line Interface and Octal T1/E1 Monitor
39
Lucent Technologies Inc.
Line Interface Units: Loopbacks
The device has three independent loopback paths that are activated using LOOPA and LOOPB (registers 6 to 9,
bits 3 and 4) as shown in Table 17. The locations of these loopbacks are illustrated in Figure 1.
Table 17. Loopback Control
* During the transmit AIS condition, the looped data will be the transmitted data from the
system and not the all-1s signal.
Transmit AIS request is ignored.
Full Local Loopback (FLLOOP)
A full local loopback (FLLOOP) connects the transmit line driver input to the receiver analog front-end circuitry.
Valid transmit output data continues to be sent to the network. If the transmit AIS (all-1s signal) is sent to the net-
work, the looped data is not affected. The ALOS alarm continues to monitor the receive line interface signal while
DLOS monitors the looped data.
See Digital Loss of Signal (DLOS) Alarm section on page 24 regarding the behavior of the DLOS alarm upon acti-
vation of FLLOOP
Remote Loopback (RLOOP)
A remote loopback (RLOOP) connects the recovered clock and retimed data to the transmitter at the system inter-
face and sends the data back to the line. The receiver front end, clock/data recovery, encoder/decoder (if enabled)
jitter attenuator (if enabled), and transmit driver circuitry are all exercised during this loopback. The transmit clock,
transmit data, and XAIS inputs are ignored. Valid receive output data continues to be sent to the system interface.
This loopback mode is very useful for isolating failures between systems.
See Loss of Transmit Clock (LOTC) Alarm and Transmit Driver Monitor (TDM) Alarm on page 31 regarding the
behavior of the LOTC and TDM alarms upon activation and deactivation of RLOOP
Digital Local Loopback (DLLOOP)
A digital local loopback (DLLOOP) connects the transmit clock and data through the encoder/decoder pair to the
receive clock and data output pins at the system interface. This loopback is operational if the encoder/decoder pair
is enabled or disabled. The AIS signal can be transmitted without any effect on the looped signal.
Operation
Symbol
LOOPA
LOOPB
Normal
Full Local Loopback
Remote Loopback
Digital Local Loopback
—
0
0
1
1
0
1
0
1
FLLOOP*
RLOOP
DLLOOP
相關PDF資料
PDF描述
T7705A SUPPLY-VOLTAGE SUPERVISORS
T8100A H.100/H.110 Interface and Time-Slot Interchanger(H.100/H.110接口和干線時間段交換機)
T8100 H.100/H.110 Interface and Time-Slot Interchanger(H.100/H.110接口和干線時隙交換機)
T8102 H.100/H.110 Interface and Time-Slot Interchanger(H.100/H.110接口和干線時隙交換機)
T8105 H.100/H.110 Interface and Time-Slot Interchanger(H.100/H.110接口和干線時隙交換機)
相關代理商/技術參數
參數描述
T77 制造商:Thomas & Betts 功能描述:2-1/2"CONDUIT BODY,IRON,T,F-7 制造商:Cooper Crouse-Hinds 功能描述: 制造商:Thomas & Betts 功能描述:Fittings T-Fitting 2.5inch Non-Thread Iron
T7700 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Core2 Duo Processors and Core2 Extreme Processors for Platforms Based on Mobile 965 Express Chipset Family
T77000150 制造商:Assembly Value Added 功能描述:
T7705102CA 制造商:Texas Instruments 功能描述:
T7705A 制造商:TI 制造商全稱:Texas Instruments 功能描述:SUPPLY-VOLTAGE SUPERVISORS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*