參數資料
型號： TLE6266G
廠商： INFINEON TECHNOLOGIES AG
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PDSO28
封裝： 18 MM, PLASTIC, SOP-28
文件頁數： 15/50頁
文件大?。?/td> 1020K
代理商： TLE6266G
Datasheet TLE 6266 G
Version 2.21
22
July 29th, 2005
7
Explanation of the Mode Transitions
To better understand the description, the reader has to be familiar with the Chapter 6.
All descriptions are starting from the normal mode, as the main operation mode. This
means, the component was powered up before and after the power up procedure
automaticaly in the Vbat stand-by mode.
Now, the watchdog circuit has to be operated correctly to switch the component in the
other modes ( details see Chapter 6). So the starting point is the TLE 6266 in normal
mode with a correct triggered watchdog like shown in Figure 8,9,10.
Normal Mode and Cyclic HS ON
In normal mode, the watchdog has to be triggered within the open window with a
dedicated SPI input command (Watchdog Trigger IBit 0, alternatively HIGH, LOW,...).
The CAN bus communication is active and a message can be transfered/received. After
the correct SPI input command to change into the Cyclic HS mode, the HS3 switch gets
activated. In parallel a long open window is started, wich has to be triggered. This mode
can be operated as long as the watchdog is triggered correctly. In this mode, no
communication is possible but an external circuit can be supplied by HS3. CANL is
pulled up to Vs by the RTL termination, CANH is pulled to GND via RTH.
Cyclic HS OFF mode
To switch from HS ON to HS OFF, the PWM input has to be triggered with a falling egde.
This is called the PWM failsafe trigger to avoid unwanted transitions into the HS OFF
mode. In the HS OFF mode the HS3 switch is deactivated and the lowest power
consumption is achieved. The LDO monitors Vcc and switches on/off due to a special
control mechanism explained in Chapter 6.5. Three possibilities can switch the TLE
6266 back to the cyclic wake HS ON mode:
7.1
CAN Bus Wake-Up
CANL is pulled to Vs. A signal transition at CANL below a certain wake-up threshold
causes a wake up and automatic transition into the cyclic HS ON mode (see Figure 8).
HS3 is activated again and also the long open window of the watchdog mechanism. The
watchdog has to be triggered correctly from that time on. If the signal at the PWM pin
makes a HIGH to LOW transition, the device switches to HS OFF again.
This wake up via the CAN bus message is flagged to the C by setting the RxD output
pin from HIGH to LOW. The reason for this behavior is to indicate the C a wake up
request. Now, the C is able to activate the whole module to serve the requested action
by the bus system.
相關PDF資料
PDF描述
TLE6280GP BRUSHLESS DC MOTOR CONTROLLER, PDSO36
TLE6361G SWITCHING REGULATOR, 425 kHz SWITCHING FREQ-MAX, PDSO36
TLE6363G DUAL SWITCHING CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO14
TLE6365G SWITCHING REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDSO8
TLE6387GV60 1 A SWITCHING CONTROLLER, 430 kHz SWITCHING FREQ-MAX, PDSO14
相關代理商/技術參數
參數描述
TLE6266GNT 制造商:Infineon Technologies AG 功能描述:CAN 125KBd Shutdown 5V Automotive 28-Pin DSO
TLE6270R 功能描述:基準電壓& 基準電流 POWERTRAIN RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel
TLE6270RAUMA1 制造商:Infineon Technologies AG 功能描述:QUAD LOW SIDE INJECTOR DRIVER 制造商:Infineon Technologies AG 功能描述:ENGINECONTROL_IC - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC DRIVER INJECTOR QUAD DSO-36
TLE6280 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:3-Phase Bridge Driver IC
TLE6280GP 功能描述:馬達/運動/點火控制器和驅動器 GATE DRIVER ICS FOR EXTERNAL MOSFETS RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*