參數資料
型號： TLE6266G
廠商： INFINEON TECHNOLOGIES AG
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PDSO28
封裝： 18 MM, PLASTIC, SOP-28
文件頁數： 5/50頁
文件大?。?/td> 1020K
代理商： TLE6266G
Datasheet TLE 6266 G
Version 2.21
13
July 29th, 2005
bus lines is affected by a bus line failure) the EME performance of the system is
degraded from the differential mode.
Figure 5
Testing the Bus Connection in Receive-only Mode
6.3
Bus Failure Management
There are 9 different CAN bus wiring failures defined by the ISO 11519-2/ISO 11898-3
standard. These failures are devided into 7 failure groups (see Table 4). The difference
between ISO11898-3 and ISO 11519-2 is also shown in Table 4. When a bus wiring
failure is detected the device automatically switches to a dedicated CANH or CANL
single-wire mode to maintain the communication if necessary. Therefore it is equipped
with one differential receiver and four single ended comparators (two for each bus line).
To avoid false triggering by external RF influences, the single wire modes are activated
after a certain delay time. As soon as the bus failure disappears the transceiver switches
back to differential mode after another time delay.
The differential receiver threshold is set to typ. -2.5V. This ensures correct reception in
the normal operation mode as well as in the failure cases 1, 2, 3a(6a) and 4(5) with a
noise margin as high as possible. When one of the bus failures 3(6), 5(4), 6(3), 6a(3a),
and 7 is detected, the defective bus wire is disabled by switching off the affected bus
termination and output stage. The failure cases in brackets() are the failure cases
according to ISO 11898-3. Simultaneously the multiplexing output of the receiver circuit
is switched to the unaffected single ended comparator
The bus failures are monitored via the diagnosis protocoll of the SPI. Therefore it is
possible to distinguish 6 CAN bus failures or failure groups on the SPI output bits 8 to 13
(see Table 4 and 5). The failures are reported until transmission of the next CAN word
begins.
1
2
5
4
3
相關PDF資料
PDF描述
TLE6280GP BRUSHLESS DC MOTOR CONTROLLER, PDSO36
TLE6361G SWITCHING REGULATOR, 425 kHz SWITCHING FREQ-MAX, PDSO36
TLE6363G DUAL SWITCHING CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO14
TLE6365G SWITCHING REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDSO8
TLE6387GV60 1 A SWITCHING CONTROLLER, 430 kHz SWITCHING FREQ-MAX, PDSO14
相關代理商/技術參數
參數描述
TLE6266GNT 制造商:Infineon Technologies AG 功能描述:CAN 125KBd Shutdown 5V Automotive 28-Pin DSO
TLE6270R 功能描述:基準電壓& 基準電流 POWERTRAIN RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel
TLE6270RAUMA1 制造商:Infineon Technologies AG 功能描述:QUAD LOW SIDE INJECTOR DRIVER 制造商:Infineon Technologies AG 功能描述:ENGINECONTROL_IC - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC DRIVER INJECTOR QUAD DSO-36
TLE6280 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:3-Phase Bridge Driver IC
TLE6280GP 功能描述:馬達/運動/點火控制器和驅動器 GATE DRIVER ICS FOR EXTERNAL MOSFETS RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*