參數資料
型號： TMS320C6414TBCLZ6
廠商： Texas Instruments
文件頁數： 116/146頁
文件大?。?/td> 0K
描述： IC DSP FIXED POINT 532FC/CSP
標準包裝： 60
系列： TMS320C6414T/15T/16T
類型： 定點
接口： 主機接口，McBSP，PCI，UTOPIA
時鐘速率： 600MHz
非易失內存： 外部
芯片上RAM： 1.03MB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.10V
工作溫度： 0°C ~ 90°C
安裝類型： 表面貼裝
封裝/外殼： 532-BFBGA，F(xiàn)CCSP
供應商設備封裝： 532-FC/CSP（23x23）
包裝： 管件
TMS320C6414T, TMS320C6415T, TMS320C6416T
FIXEDPOINT DIGITAL SIGNAL PROCESSORS
SPRS226M NOVEMBER 2003 REVISED APRIL 2009
71
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
31
16
15
14
13
12
11
10
9
8
Reserved
Enable or
Non-Enabled
Interrupt Wake
Enabled
Interrupt Wake
PD3
PD2
PD1
R/W-0
7
0
Legend: R/Wx = Read/write reset value
NOTE: The shadowed bits are not part of the power-down logic discussion and therefore are not covered here. For information on these other
bit fields in the CSR register, see the TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189).
Figure 10. PWRD Field of the CSR Register
A delay of up to nine clock cycles may occur after the instruction that sets the PWRD bits in the CSR before the
PD mode takes effect. As best practice, NOPs should be padded after the PWRD bits are set in the CSR to account
for this delay.
If PD1 mode is terminated by a non-enabled interrupt, the program execution returns to the instruction where
PD1 took effect. If PD1 mode is terminated by an enabled interrupt, the interrupt service routine will be executed
first, then the program execution returns to the instruction where PD1 took effect. In the case with an enabled
interrupt, the GIE bit in the CSR and the NMIE bit in the interrupt enable register (IER) must also be set in order
for the interrupt service routine to execute; otherwise, execution returns to the instruction where PD1 took effect
upon PD1 mode termination by an enabled interrupt.
PD2 and PD3 modes can only be aborted by device reset. Table 32 summarizes all the power-down modes.
Table 32. Characteristics of the Power-Down Modes
PRWD FIELD
(BITS 1510)
POWER-DOWN
MODE
WAKE-UP METHOD
EFFECT ON CHIP’S OPERATION
000000
No power-down
—
001001
PD1
Wake by an enabled interrupt
CPU halted (except for the interrupt logic)
Power-down mode blocks the internal clock inputs at the
010001
PD1
Wake by an enabled or
non-enabled interrupt
Power-down mode blocks the internal clock inputs at the
boundary of the CPU, preventing most of the CPU’s logic from
switching. During PD1, EDMA transactions can proceed
between peripherals and internal memory.
011010
PD2
Wake by a device reset
Output clock from PLL is halted, stopping the internal clock
structure from switching and resulting in the entire chip being
halted. All register and internal RAM contents are preserved. All
functional I/O “freeze” in the last state when the PLL clock is
turned off.
When entering PD2 and PD3, all functional I/O remains in the previous state. However, for peripherals which are asynchronous in nature or
peripherals with an external clock source, output signals may transition in response to stimulus on the inputs. Under these conditions,
peripherals will not operate according to specifications.
相關PDF資料
PDF描述
ZL9101MIRZ MODULE DGTL DC-DC 12A 21QFN
EBM18DRKN-S13 CONN EDGECARD 36POS .156 EXTEND
VI-B1F-CY-F1 CONVERTER MOD DC/DC 72V 50W
VI-J32-IZ CONVERTER MOD DC/DC 15V 25W
HWS30-12/A PWR SUP IND 12V 2.5A SNG OUTPUT
相關代理商/技術參數
參數描述
TMS320C6414TBCLZ7 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZ8 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZA6 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZA7 制造商:Texas Instruments 功能描述:
TMS320C6414TBCLZA8 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*