參數資料
型號: TMS320C6414TBCLZ6
廠商: Texas Instruments
文件頁數: 93/146頁
文件大?。?/td> 0K
描述: IC DSP FIXED POINT 532FC/CSP
標準包裝: 60
系列: TMS320C6414T/15T/16T
類型: 定點
接口: 主機接口,McBSP,PCI,UTOPIA
時鐘速率: 600MHz
非易失內存: 外部
芯片上RAM: 1.03MB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 1.10V
工作溫度: 0°C ~ 90°C
安裝類型: 表面貼裝
封裝/外殼: 532-BFBGA,F(xiàn)CCSP
供應商設備封裝: 532-FC/CSP(23x23)
包裝: 管件
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁當前第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁
TMS320C6414T, TMS320C6415T, TMS320C6416T
FIXEDPOINT DIGITAL SIGNAL PROCESSORS
SPRS226M NOVEMBER 2003 REVISED APRIL 2009
50
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
Terminal Functions (Continued)
SIGNAL
TYPE
IPD/
DESCRIPTION
NAME
NO.
TYPE
IPD/
IPU
DESCRIPTION
EMIFB (16-BIT) ADDRESS||k
BEA20
E16
IPU
EMIFB external address (half-word address) (O/Z)
Also controls initialization of DSP modes at reset (I) via pullup/pulldown resistors
Device Endian mode
BEA19
D18
IPU
Also controls initialization of DSP modes at reset (I) via pullup/pulldown resistors
Device Endian mode
BEA20:
0
Big Endian
1
Little Endian (default mode)
BEA18
C18
1
Little Endian (default mode)
Boot mode
BEA[19:18]: 00 –
No boot
01 HPI boot
BEA17
B18
BEA[19:18]: 00 –
No boot
01 HPI boot
10 EMIFB 8-bit ROM boot with default timings (default mode)
11 Reserved
BEA16
A18
11 Reserved
EMIF clock select
BEA15
D17
EMIF clock select
BEA[17:16]: Clock mode select for EMIFA (AECLKIN_SEL[1:0])
00 –
AECLKIN (default mode)
01 CPU/4 Clock Rate
BEA14
C17
01 CPU/4 Clock Rate
10 CPU/6 Clock Rate
11 Reserved
BEA13
B17
11 Reserved
BEA[15:14]: Clock mode select for EMIFB (BECLKIN_SEL[1:0])
00 –
BECLKIN (default mode)
BEA12
A17
BEA[15:14]: Clock mode select for EMIFB (BECLKIN_SEL[1:0])
00 –
BECLKIN (default mode)
01 CPU/4 Clock Rate
10 CPU/6 Clock Rate
BEA11
D16
10 CPU/6 Clock Rate
11 Reserved
BEA10
C16
I/O/Z
IPD
PCI EEPROM Auto-Initialization (EEAI) [C6415T and C6416T devices only]
BEA13:
PCI auto-initialization via external EEPROM
If the PCI peripheral is disabled (PCI_EN pin = 0), this pin must not be pulled up.
BEA9
B16
I/O/Z
IPD
If the PCI peripheral is disabled (PCI_EN pin = 0), this pin must not be pulled up.
0
PCI auto-initialization through EEPROM is disabled (default).
1
PCI auto-initialization through EEPROM is enabled.
BEA8
A16
1
PCI auto-initialization through EEPROM is enabled.
UTOPIA Enable (UTOPIA_EN) [C6415T and C6416T devices only]
BEA11:
UTOPIA peripheral enable (functional)
BEA7
D15
UTOPIA Enable (UTOPIA_EN) [C6415T and C6416T devices only]
BEA11:
UTOPIA peripheral enable (functional)
0
UTOPIA disabled (McBSP1 enabled) [default]
1
UTOPIA enabled (McBSP1 disabled)
BEA6
C15
1
UTOPIA enabled (McBSP1 disabled)
The C6414T device does not support the PCI and UTOPIA peripherals; for proper device
do not
BEA5
B15
The C6414T device does not support the PCI and UTOPIA peripherals; for proper device
operation, do not oppose the internal pulldowns (IPDs) on the BEA13 and BEA11 pins.
Also for proper C6414T device operation, do not oppose the IPDs on the BEA7, BEA8,
BEA4
A15
Also for proper C6414T device operation, do not oppose the IPDs on the BEA7, BEA8,
and BEA9 pins.
BEA3
D14
For proper C6415T device operation, the BEA7 pin must be externally pulled up with a
1-k
resistor.
BEA2
C14
1-k
resistor.
For proper C6416T device operation, the BEA8 and BEA9 pins must be externally
pulled up with a 1-k
resistor.
BEA1
A14
pulled up with a 1-k
resistor.
For more details, see the Device Configurations section of this data sheet.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-k IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-k
resistor should be used.)
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
kTo maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
相關PDF資料
PDF描述
ZL9101MIRZ MODULE DGTL DC-DC 12A 21QFN
EBM18DRKN-S13 CONN EDGECARD 36POS .156 EXTEND
VI-B1F-CY-F1 CONVERTER MOD DC/DC 72V 50W
VI-J32-IZ CONVERTER MOD DC/DC 15V 25W
HWS30-12/A PWR SUP IND 12V 2.5A SNG OUTPUT
相關代理商/技術參數
參數描述
TMS320C6414TBCLZ7 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZ8 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZA6 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZA7 制造商:Texas Instruments 功能描述:
TMS320C6414TBCLZA8 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS