參數資料
型號： TMS320C6414TBCLZ6
廠商： Texas Instruments
文件頁數： 96/146頁
文件大小： 0K
描述： IC DSP FIXED POINT 532FC/CSP
標準包裝： 60
系列： TMS320C6414T/15T/16T
類型： 定點
接口： 主機接口，McBSP，PCI，UTOPIA
時鐘速率： 600MHz
非易失內存： 外部
芯片上RAM： 1.03MB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.10V
工作溫度： 0°C ~ 90°C
安裝類型： 表面貼裝
封裝/外殼： 532-BFBGA，F(xiàn)CCSP
供應商設備封裝： 532-FC/CSP（23x23）
包裝： 管件
TMS320C6414T, TMS320C6415T, TMS320C6416T
FIXEDPOINT DIGITAL SIGNAL PROCESSORS
SPRS226M NOVEMBER 2003 REVISED APRIL 2009
53
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
Terminal Functions (Continued)
SIGNAL
TYPE
IPD/
DESCRIPTION
NAME
NO.
TYPE
IPD/
IPU
DESCRIPTION
UNIVERSAL TEST AND OPERATIONS PHY INTERFACE FOR ASYNCHRONOUS TRANSFER MODE (ATM) [UTOPIA SLAVE]
[C6415T and C6416T devices only]
UTOPIA SLAVE (ATM CONTROLLER) TRANSMIT INTERFACE
UXCLKY
AD11
I
h
Source clock for UTOPIA transmit driven by Master ATM Controller.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
UXCLAVY
AC14
O/Z
Transmit cell available status output signal from UTOPIA Slave.
0
indicates a complete cell is NOT available for transmit
1
indicates a complete cell is available for transmit
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
UXENBY
AE15
I
UTOPIA transmit interface enable input signal. Asserted by the Master ATM Controller to indi-
cate that the UTOPIA Slave should put out on the Transmit Data Bus the first byte of valid data
and the UXSOC signal in the next clock cycle.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
UXSOCY
AC13
O/Z
Transmit Start-of-Cell signal. This signal is output by the UTOPIA Slave on the rising edge of
the UXCLK, indicating that the first valid byte of the cell is available on the 8-bit Transmit Data
Bus (UXDATA[7:0]).
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
DX1/
UXADDR4§
AB11
I/O/Z
McBSP1 [default] or UTOPIA transmit address pins
As UTOPIA transmit address pins UXADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:
5-bit Slave transmit address input pins driven by the Master ATM Controller to identify and
select one of the Slave devices (up to 31 possible) in the ATM System.
UXADDR0 pin is tied off when the UTOPIA peripheral is disabled [UTOPIA_EN
(BEA11 pin) = 0]
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHAN-
NEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
FSX1/
UXADDR3§
AB13
I/O/Z
McBSP1 [default] or UTOPIA transmit address pins
As UTOPIA transmit address pins UXADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:
FSR1/
UXADDR2§
AC9
I/O/Z
As UTOPIA transmit address pins UXADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:
5-bit Slave transmit address input pins driven by the Master ATM Controller to identify and
select one of the Slave devices (up to 31 possible) in the ATM System.
DR1/
UXADDR1§
AF11
I
UXADDR0 pin is tied off when the UTOPIA peripheral is disabled [UTOPIA_EN
(BEA11 pin) = 0]
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHAN-
UXADDR0Y
AE9
I
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHAN-
NEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-k IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-k
resistor should be used.)
§ For the C6415T and C6416T devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414T device does not support the PCI or UTOPIA peripherals; therefore, these muxed peripheral pins are standalone peripheral functions
for this device.
hFor the C6415T and C6416T devices, external pulldowns required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other
devices, then a 10-k
resistor must be used to externally pull down each of these pins. If these pins are “no connects”, then only UXCLK and
URCLK need to be pulled down and other pulldowns are not necessary.
For the C6415T and C6416T devices, external pullups required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices,
then a 10-k
resistor must be used to externally pull up each of these pins. If these pins are “no connects”, then the pullups are not necessary.
ΨThe C6414T device does not support the UTOPIA peripheral; therefore, these standalone UTOPIA pins are Reserved (leave unconnected, do
not connect to power or ground) with the exception of UXCLK and URCLK which should be connected to a 10-k
pulldown resistor (see the
square [
h] footnote).
相關PDF資料
PDF描述
ZL9101MIRZ MODULE DGTL DC-DC 12A 21QFN
EBM18DRKN-S13 CONN EDGECARD 36POS .156 EXTEND
VI-B1F-CY-F1 CONVERTER MOD DC/DC 72V 50W
VI-J32-IZ CONVERTER MOD DC/DC 15V 25W
HWS30-12/A PWR SUP IND 12V 2.5A SNG OUTPUT
相關代理商/技術參數
參數描述
TMS320C6414TBCLZ7 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZ8 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZA6 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZA7 制造商:Texas Instruments 功能描述:
TMS320C6414TBCLZA8 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*