參數資料
型號： TMS320C6414TBCLZ6
廠商： Texas Instruments
文件頁數： 79/146頁
文件大?。?/td> 0K
描述： IC DSP FIXED POINT 532FC/CSP
標準包裝： 60
系列： TMS320C6414T/15T/16T
類型： 定點
接口： 主機接口，McBSP，PCI，UTOPIA
時鐘速率： 600MHz
非易失內存： 外部
芯片上RAM： 1.03MB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.10V
工作溫度： 0°C ~ 90°C
安裝類型： 表面貼裝
封裝/外殼： 532-BFBGA，F(xiàn)CCSP
供應商設備封裝： 532-FC/CSP（23x23）
包裝： 管件
TMS320C6414T, TMS320C6415T, TMS320C6416T
FIXEDPOINT DIGITAL SIGNAL PROCESSORS
SPRS226M NOVEMBER 2003 REVISED APRIL 2009
38
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
DEVICE CONFIGURATIONS (CONTINUED)
Table 27. PCI_EN and MCBSP2_EN Peripheral Selection (HPI, GP[15:9], PCI, and McBSP2)
PERIPHERAL SELECTION
PERIPHERALS SELECTED
PCI_EN
Pin [AA4]
MCBSP2_EN
Pin [AF3]
HPI
GP[15:9]
PCI
EEPROM
(Internal to PCI)
McBSP2
0
√
0
1
√
1
0
√
1
√
The PCI_EN pin must be driven valid at all times and the user must not switch values throughout device operation.
The MCBSP2_EN pin must be driven valid at all times and the user can switch values throughout device operation.
The only time McBSP2 is disabled is when both PCI_EN = 1 and MCBSP2_EN = 0. This configuration enables, at reset, the auto-initialization
of the PCI peripheral through the PCI internal EEPROM [provided the PCI EEPROM Auto-Initialization pin (BEA13) is pulled up
(EEAI = 1)]. The user can then enable the McBSP2 peripheral (disabling EEPROM) by dynamically changing MCBSP2_EN to a “1” after the
device is initialized (out of reset).
If the PCI is disabled (PCI_EN = 0), the HPI peripheral is enabled and GP[15:9] pins can be programmed
as GPIO, provided the GPxEN and GPxDIR bits are properly configured. [Note: The PCI_EN pin must
be driven valid at all times and the user must not switch values throughout device operation.]
This means all multiplexed HPI/PCI pins function as HPI and all standalone PCI pins (PCBE0 and
XSP_CS) are tied-off (Hi-Z). Also, the multiplexed GPIO/PCI pins can be used as GPIO with the
proper software configuration of the GPIO enable and direction registers (for more details, see
Table 29).
If the PCI is enabled (PCI_EN = 1), the HPI peripheral is disabled. [Note: The PCI_EN pin must be driven
valid at all times and the user must not switch values throughout device operation.]
This means all multiplexed HPI/PCI pins function as PCI. Also, the multiplexed GPIO/PCI pins function
as PCI pins (for more details, see Table 29).
The MCBSP2_EN pin, in combination with the PCI_EN pin, controls the selection of the McBSP2
peripheral and the PCI internal EEPROM (for more details, see Table 27 and its footnotes). [Note: The
MCBSP2_EN pin must be driven valid at all times and the user can switch values throughout device
operation.]
other device configurations
Table 28 describes the C6414T, C6415T, and C6416T devices configuration pins, which are set up via external
pullup/pulldown resistors through the specified EMIFB address bus pins (BEA[20:13, 11, 9:7]) and the HD5 pin.
For more details on these device configuration pins, see the Terminal Functions table and the Debugging
Considerations section.
相關PDF資料
PDF描述
ZL9101MIRZ MODULE DGTL DC-DC 12A 21QFN
EBM18DRKN-S13 CONN EDGECARD 36POS .156 EXTEND
VI-B1F-CY-F1 CONVERTER MOD DC/DC 72V 50W
VI-J32-IZ CONVERTER MOD DC/DC 15V 25W
HWS30-12/A PWR SUP IND 12V 2.5A SNG OUTPUT
相關代理商/技術參數
參數描述
TMS320C6414TBCLZ7 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZ8 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZA6 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMS320C6414TBCLZA7 制造商:Texas Instruments 功能描述:
TMS320C6414TBCLZA8 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*