參數資料
型號： TS83102G0BCGL
廠商： E2V TECHNOLOGIES PLC
元件分類： ADC
英文描述： 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CBGA152
封裝： 21 X 21 MM, 1.27 MM PITCH, CERAMIC, BGA-152
文件頁數： 40/60頁
文件大小： 1510K
代理商： TS83102G0BCGL
45
0830E–BDC–06/07
e2v semiconductors SAS 2007
TS83102G0B
the ADC’s output bits should toggle from 0 to 1 successively, giving sequences such as 0101010101 and
1010101010 every 2 cycles. This function is disabled when PGEB is left floating or connected to Ground.
13.7.5
DECB/DIODE: Junction Temperature Monitoring and Output Decimation Enable
The DECB/DIODE pin is provided to enable the decimation function and monitor the die junction
temperature.
When V
EE = -5V, the ADC runs in “decimation by 32” mode (1 out of 32 data is output from the ADC, thus
reducing the data rate by 32).
When the DECB/DIODE pin is left floating or connected to Ground, then the ADC is said to be in a "nor-
mal" mode of operation (the output data is not decimated) and can be used for die junction temperature
monitoring only.
If you do not intend to use the die junction temperature monitoring function, the DECB/DIODE pin (A10)
has to be left either floating or connected to ground.
The decimation function can be used to debug the ADC at initial stages. This function enables you to
reduce the ADC output rate by 32, thus reducing the time of the ADC’s debug phase at the maximum
speed rate, and is compatible with industrial testing environments.
When this function is active, the ADC outputs only 1 out of 32 bits of data, resulting in a data rate 32
times slower than the clock rate.
Note:
The ADC decimation test mode is different from the pattern generator function, which is used to check the
ADC’s outputs.
13.7.6
External Configuration Description
Because of the use of one internal diode-mounted transistor (used for junction temperature monitoring),
you have to implement external head-to-tail protection diodes so as to avoid potential reverse current
flows, which can damage the internal diode component.
Two external configurations are possible:
Configuration 1: allows both junction temperature monitoring and output data decimation.
Configuration 2: allows junction temperature monitoring only.
13.7.6.1
Configuration 1
This external configuration allows you to apply the requested levels to activate output data decimation
(V
EE = -5V) and at the same time monitor the junction temperature diode (this explains why 7 protection
diodes are needed in the other direction, as shown in Figure 51).
相關PDF資料
PDF描述
TS83110CZT 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDFP28
TS83110MZT 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDFP28
TS83110VZT 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDFP28
TS83110MZB/T 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDSO28
TS83110VS 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
相關代理商/技術參數
參數描述
TS83102G0BVGL 制造商:e2v technologies 功能描述:ADC SGL 2GSPS 10-BIT PARALLEL 152CBGA - Trays
TS83102G0CGL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog to Digital Converter
TS83102G0GSZR5 制造商:e2v technologies 功能描述:TS83102G0GSZR5 - Trays
TS831-3I 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MICROPOWER VOLTAGE SUPERVISOR RESET ACTIVE LOW
TS831-3ID 功能描述:監控電路 2.71V Micropower AL RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*