參數資料
型號: UPD753036GC
廠商: NEC Corp.
英文描述: DIODE ZENER SINGLE 500mW 47Vz 2.7mA-Izt 0.05 0.1uA-Ir 36Vr DO35-GLASS 5K/REEL
中文描述: 4位單片機
文件頁數: 86/88頁
文件大小: 483K
代理商: UPD753036GC
86
μ
PD753036, 753036(A)
Data Sheet U11353EJ4V0DS00
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note:
Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity
as much as possible, and quickly dissipate it once, when it has occurred. Environmental control
must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using
insulators that easily build static electricity. Semiconductor devices must be stored and transported
in an anti-static container, static shielding bag or conductive material. All test and measurement
tools including work bench and floor should be grounded. The operator should be grounded using
wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need
to be taken for PW boards with semiconductor devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS
Note:
No connection for CMOS device inputs can be cause of malfunction. If no connection is provided
to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence
causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels
of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused
pin should be connected to V
DD
or GND with a resistor, if it is considered to have a possibility of
being an output pin. All handling related to the unused pins must be judged device by device and
related specifications governing the devices.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note:
Power-on does not necessarily define initial status of MOS device. Production process of MOS
does not define the initial operation status of the device. Immediately after the power source is
turned ON, the devices with reset function have not yet been initialized. Hence, power-on does
not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the
reset signal is received. Reset operation must be executed immediately after power-on for devices
having reset function.
相關PDF資料
PDF描述
UPD753036GCA DIODE ZENER SINGLE 500mW 60Vz 2.1mA-Izt 0.05 0.1uA-Ir 46Vr DO35-GLASS 5K/REEL
UPD753036GK DIODE ZENER SINGLE 500mW 75Vz 1.7mA-Izt 0.05 0.1uA-Ir 56Vr DO35-GLASS 5K/REEL
UPD753104 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER
UPD753104GC 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER
UPD753104GK 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER
相關代理商/技術參數
參數描述
UPD75304GF-407-3B9 制造商:Renesas Electronics Corporation 功能描述:
UPD75306G182 制造商:Panasonic Industrial Company 功能描述:IC
UPD75308F478 制造商:Panasonic Industrial Company 功能描述:IC
UPD75308G699 制造商:Panasonic Industrial Company 功能描述:IC
UPD753204013 制造商:Panasonic Industrial Company 功能描述:IC