- 您現在的位置：買賣IC網 > PDF目錄225499 > V58C2128404SBLT6I (PROMOS TECHNOLOGIES INC) 32M X 4 DDR DRAM, 0.7 ns, PDSO66 PDF資料下載
參數資料
| 型號： | V58C2128404SBLT6I |
| 廠商： | PROMOS TECHNOLOGIES INC |
| 元件分類： | DRAM |
| 英文描述： | 32M X 4 DDR DRAM, 0.7 ns, PDSO66 |
| 封裝： | 0.400 X 0.875 INCH, PLASTIC, MS-024FC, TSOP2-66 |
| 文件頁數： | 17/60頁 |
| 文件大?。?/td> | 915K |
| 代理商： | V58C2128404SBLT6I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
24
V58C2128(804/404/164)SB*I Rev. 1.3 March 2006
ProMOS TECHNOLOGIES
V58C2128(804/404/164)SB*I
Read Interrupted by a Write
To interrupt a Burst Read with a Write command, a Burst Stop command must be asserted to stop the burst
read operation and 3-state the DQ bus. Additionally, control of the DQS bus must be turned around to allow
the memory controller to drive the data strobe signal (DQS) into the DDR SDRAM for the write cycles. Once
the Burst Stop command has been issued, a Write command can not be issued until a minimum delay or
latency (L
BST) has been satisfied. This latency is measured from the Burst Stop command and is equivalent
to the CAS latency programmed into the mode register. In instances where CAS latency is measured in half
clock cycles, the minimum delay (L
BST) is rounded up to the next full clock cycle (i.e., if CL=2 then LBST=2, if
CL=2.5 then L
BST=3). It is illegal to interrupt a Read with autoprecharge command with a Write command.
Read Interrupted by Burst Stop Command Followed by a Write Command Timing
Write Interrupted by a Write
A Burst Write can be interrupted before completion by a new Write command to any bank. When the pre-
vious burst is interrupted, the remaining addresses are overridden with a full burst length starting with the new
address. The data from the first Write command continues to be input into the device until the Write Latency
of the interrupting Write command is satisfied (WL=1) At this point, the data from the interrupting Write com-
mand is input into the device. Write commands can be issued on each rising edge of the system clock. It is
illegal to interrupt a Write with autoprecharge command with a Write command.
Write Interrupted by a Write Command Timing
(CAS Latency = 2; Burst Length = 4)
T0
T1
T2
T3
T4
T5
T6
T7
T8
BST
NOP
Write
NOP
D0
D1
Read
D0
D1
D2
D3
CK, CK
Command
DQS
DQ
T9
LBST
(CAS Latency = Any; Burst Length = 4)
T0
T1
T2
T3
T4
T5
T6
T7
T8
WriteA
NOP
WriteB
NOP
DA0 DA1 DB0 DB1 DB2 DB3
CK, CK
Command
DQS
DQ
DM
T9
Write Latency
DM0 DM1 DM0 DM1 DM2 DM3
相關PDF資料 |
PDF描述 |
|---|---|
| V58C365164S5 | 4M X 16 DDR DRAM, 0.1 ns, PDSO66 |
| V608ME06 | VCO, 1900 MHz - 2270 MHz |
| V603ME07 | VCO, 1896 MHz - 1924 MHz |
| V6049001 | VCO, 1600 MHz - 2200 MHz |
| V610ME04 | VCO, 1950 MHz - 2150 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V58C2128804S | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:HIGH PERFORMANCE 2.5 VOLT 128 Mbit DDR SDRAM |
| V58C2256 | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:HIGH PERFORMANCE 2.5 VOLT 256 Mbit DDR SDRAM |
| V58C2256164S | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:HIGH PERFORMANCE 2.5 VOLT 256 Mbit DDR SDRAM |
| V58C2256324SAB30 | 制造商:Marvell 功能描述:Marvell V58C2256324SAB30 |
| V58C2256324SAB33 | 制造商:Marvell 功能描述:Marvell V58C2256324SAB33 |
發布緊急采購，3分鐘左右您將得到回復。