參數資料
型號: XR17L152IM
廠商: EXAR CORP
元件分類: 微控制器/微處理器
英文描述: CAP .068UF 400V PEN FILM 2825 5%
中文描述: 2 CHANNEL(S), 3.125M bps, SERIAL COMM CONTROLLER, PQFP100
封裝: 14 X 14 MM, 1 MM HEIGHT, TQFP-100
文件頁數: 3/55頁
文件大?。?/td> 318K
代理商: XR17L152IM
XR17L152
3.3V PCI BUS DUAL UART
REV. 1.1.0
á
DISCONTINUED
3
PIN DESCRIPTIONS
N
AME
P
IN
#
T
YPE
D
ESCRIPTION
PCI LOCAL BUS INTERFACE
RST#
86
I
Bus reset input (active low). It resets the PCI local bus configuration space
registers, device configuration registers and UART channel registers to the
default condition, see
Table 18
.
CLK
87
I
Bus clock input of up to 33MHz at 3.3V.
AD31-AD0
90-97, 2-9,
24-31, 35-42
I/O
Address data lines [31:0] (bidirectional).
FRAME#
13
I
Bus transaction cycle frame (active low). It indicates the beginning and dura-
tion of an access.
C/BE3#
-
C/
BE0#
98, 12,
21, 34
I
Bus Command/Byte Enable [3:0] (active low). This line is multiplexed for bus
Command during the address phase and Byte Enables during the data
phase.
IRDY#
14
I
Initiator Ready (active low). During a write, it indicates that valid data is
present on data bus. During a read, it indicates the master is ready to accept
data.
TRDY#
15
O
Target Ready (active low).
STOP#
17
O
Target request to stop current transaction (active low).
IDSEL
99
I
Initialization device select (active high).
DEVSEL#
16
O
Device select to the XR17L152 (active low).
INTA#
85
OD
Device interrupt from XR17L152 (open drain, active low).
PAR
20
I/O
Parity is even across AD[31:0] and C/BE[3:0]#. (bidirectional, active high).
PERR#
18
O
Data Parity error indicator, except for Special Cycle transactions (active low).
Optional in bus target application.
SERR#
19
OD
System error indicator, Address parity or Data parity during Special Cycle
transactions (open drain, active low). Optional in bus target application.
MODEM OR SERIAL I/O INTERFACE
TX0
73
O
UART channel 0 Transmit Data or infrared transmit data. Normal TXD output
idles at logic 1 condition while infrared TXD output idles at a logic 0 condition.
RX0
66
I
UART channel 0 Receive Data or infrared receive data. Normal RXD input
idles at logic 1 condition while infrared RXD input idles at a logic 0 condition.
In the infrared mode, the polarity of the incoming RXD signal can be selected
via FCTR bit-4. If this bit is a logic 0, logic 0 on the RXD input is considered a
mark and if this bit is a logic 1, a logic 0 on the RXD input is considered a
space.
RTS0#
71
O
UART channel 0 Request to Send or general purpose output (active low). If
this output is not used, leave it unconnected.
CTS0#
67
I
UART channel 0 Clear to Send or general purpose input (active low). This
input should be connected to VCC when not used.
DTR0#
72
O
UART channel 0 Data Terminal Ready or general purpose output (active low).
If this output is not used, leave it unconnected.
相關PDF資料
PDF描述
XR17L152 3.3V PCI BUS DUAL UART
XR17L152CM 3.3V PCI BUS DUAL UART
XR2001 High-Voltage, High-Current Darlington Transistor Arrays
XR2002CN High-Voltage, High-Current Darlington Transistor Arrays
XR2003 High-Voltage, High-Current Darlington Transistor Arrays
相關代理商/技術參數
參數描述
XR17L154 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS QUAD UART
XR17L154CV 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm
XR17L154IV 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS QUAD UART
XR17V252 制造商:EXAR 制造商全稱:EXAR 功能描述:66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT
XR17V252_08 制造商:EXAR 制造商全稱:EXAR 功能描述:66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT