- 您現在的位置：買賣IC網 > PDF目錄376455 > XR17L152IM (EXAR CORP) CAP .068UF 400V PEN FILM 2825 5% PDF資料下載
參數資料
| 型號： | XR17L152IM |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | CAP .068UF 400V PEN FILM 2825 5% |
| 中文描述： | 2 CHANNEL(S), 3.125M bps, SERIAL COMM CONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 1 MM HEIGHT, TQFP-100 |
| 文件頁數： | 38/55頁 |
| 文件大?。?/td> | 318K |
| 代理商： | XR17L152IM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
á
DISCONTINUED
XR17L152
3.3V PCI BUS DUAL UART
REV. 1.1.0
38
MCR[7]: Clock Prescaler Select
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
Line Status Register (LSR)
This register provides the status of data transfers between the UART and the host. If IER bit-2 is enabled, an
LSR interrupt is generated when a received data error occurs due to Overrrun, Parity or Framing. If LSR[0] =
logic 0, then LSR bits 1-4 are invalid.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Tag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register is
overwritten. Note that under this condition the data byte in the receive shift register is not transferred into the
FIFO, therefore the data in the FIFO is not corrupted by the error. Automatic Hardware (RTS/CTS) or
Software (Xon/Xoff) Flow Control should be considered if this condition persists.
LSR[2]: Receive Data Parity Error Tag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Tag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[4]: Receive Break Flag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was a logic 0 for one character frame time). In the FIFO
mode, only one break character is loaded into the FIFO. The break indication remains until the RX input
returns to the idle condition, “mark” or logic 1.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. This bit indicates that the transmitter is ready to
accept a new character for transmission. In addition, this bit causes the UART to issue an interrupt to the host
when the THR interrupt enable is set. The THR bit is set to a logic 1 when the last data byte is transferred from
the transmit holding register to the transmit shift register. The bit is reset to logic 0 concurrently with the data
loading to the transmit holding register by the host. In the FIFO mode this bit is set when the transmit FIFO is
empty; it is cleared when at least 1 byte is written to the transmit FIFO.
LSR[6]: Transmit Shift Register Empty Flag
This bit is the Transmit Shift Register Empty indicator. This bit is set to a logic 1 whenever the transmitter goes
idle. It is set to logic 0 whenever either the THR or TSR contains a data character. In the FIFO mode this bit is
set to one whenever the transmit FIFO and transmit shift register are both empty.
相關PDF資料 |
PDF描述 |
|---|---|
| XR17L152 | 3.3V PCI BUS DUAL UART |
| XR17L152CM | 3.3V PCI BUS DUAL UART |
| XR2001 | High-Voltage, High-Current Darlington Transistor Arrays |
| XR2002CN | High-Voltage, High-Current Darlington Transistor Arrays |
| XR2003 | High-Voltage, High-Current Darlington Transistor Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17L154 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS QUAD UART |
| XR17L154CV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm |
| XR17L154IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS QUAD UART |
| XR17V252 | 制造商:EXAR 制造商全稱:EXAR 功能描述:66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT |
| XR17V252_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT |
發布緊急采購，3分鐘左右您將得到回復。