REV. 1.0.2 Timer Operation in Re-triggerable Mode: In the re-triggerable mod" />
參數資料
型號： XR17V258IV-0A-EVB
廠商： Exar Corporation
文件頁數： 15/69頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR17V258 144LQFP
標準包裝： 1
系列： *
XR17V258
22
66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
REV. 1.0.2
Timer Operation in Re-triggerable Mode:
In the re-triggerable mode, when the Timer is started, the Timer output will stay HIGH until it reaches half of the
terminal count N (= P clocks) and toggle LOW and stay LOW for a similar amount of time (Q clocks). The
above step will keep repeating until the Timer is stopped at which time the output will become HIGH (default
state). See Figure 7. Also, after the Timer is started, re-starting the Timer does not have any effect in re-
triggerable mode. The Timer must be programmed while it is stopped since the following operations are
blocked when the Timer is running:
■ Any write to TIMER MSB, LSB registers
■ Issue of any command other than ’Stop Timer’ and ’Reset Timer’ (’Start Timer’ is not allowed)
Routing the Timer Output to MPIO[0] Pin:
MPIO[0] pin is by default (on power up or reset, for example) an input. However, whenever the Timer output is
routed to MPIO[0] pin,
■ MPIO[0] will be automatically selected as an output
■ MPIO[0] will become HIGH (the default state of Timer output)
■ All MPIO control registers (MPIOLVL, MPIOSEL etc) lose control over MPIO[0] and get the control back
only when the Timer output is de-routed from MPIO[0].
FIGURE 7. TIMER OUTPUT IN ONE-SHOT AND RE-TRIGGERABLE MODES
TIMER Output in
Re-triggerable
Mode
TIMER Output in
One-Shot Mode
After 'P'
clocks
START TIMER
COMMAND ISSUED
START TIMER
COMMAND ISSUED
'N' Clocks
STOP TIMER
COMMAND ISSUED
START TIMER COMMANDS ISSUED: LESS THAN 'N'
CLOCKS BETWEEN SUCCESSIVE COMMANDS
< 'N' Clocks
After 'P'
clocks
After 'P'
clocks
After 'P'
clocks
After 'P'
clocks
After 'Q'
clocks
After 'Q'
clocks
After 'Q'
clocks
After 'Q'
clocks
< 'N' Clocks
Timer Interrupt
In the one-shot mode, the Timer will issue an interrupt upon timing out which is ’N’ clocks after the Timer is
started. In the re-triggerable mode, the Timer will keep issuing an interrupt every ’N’ clocks which is on every
rising edge of the Timer output. The Timer interrupt can be cleared by reading the TIMERCNTL register or
when a Timer Reset command is issued which brings the Timer back to its default settings. The TIMERCNTL
will read a value of 0x01 when the Timer interrupt is enabled and there is a pending interrupt. It reads a value
of 0x00 at all other times. Stopping the Timer does not clear the interrupt and neither does subsequent re-
starting.
相關PDF資料
PDF描述
GCC10DRYN-S734 CONN EDGECARD 20POS DIP .100 SLD
VI-B1Y-EV CONVERTER MOD DC/DC 3.3V 99W
155880-000 SOLDER SLEEVE 11MM DIA SHIELD
VI-2VR-EX CONVERTER MOD DC/DC 7.5V 75W
VI-2VP-EX CONVERTER MOD DC/DC 13.8V 75W
相關代理商/技術參數
參數描述
XR17V258IVF 制造商:Exar Corporation 功能描述:
XR17V258IV-F 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17V258IVTR-F 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17V352 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUAL PCI EXPRESS UART
XR17V352IB-0A-EVB 功能描述:界面開發工具 Eval Board for XR17V352IB Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*