參數資料
型號： XRT75R12D
廠商： Exar Corporation
英文描述： TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述： 第十二章通道E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數： 35/131頁
文件大?。?/td> 717K
代理商： XRT75R12D
PRELIMINARY
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. P1.0.1
30
4.4
The Transmit Pulse Shaper converts the B3ZS encoded digital pulses into a single analog Alternate Mark
Inversion (AMI) pulse that meets the industry standard mask template requirements for STS-1 and DS3. For
E3 mode, the pulse shaper converts the HDB3 encoded pulses into a single full amplitude square shaped
pulse with very little slope. The Pulse Shaper Block also includes a Transmit Build Out Circuit, which can
either be disabled or enabled by setting the TxLEV_n bit to “1” or “0” in the control register. For DS3/STS-1
rates, the Transmit Build Out Circuit is used to shape the transmit waveform that ensures that transmit pulse
template requirements are met at the Cross-Connect system. The distance between the transmitter output and
the Cross-Connect system can be between 0 to 450 feet. For E3 rate, since the output pulse template is
measured at the secondary of the transformer and since there is no Cross-Connect system pulse template
requirements, the Transmit Build Out Circuit is always disabled. The differential line driver increases the
transmit waveform to appropriate level and drives into the 75
load as shown in Figure 20.
F
IGURE
20. T
RANSMIT
P
ULSE
S
HAPE
T
EST
C
IRCUIT
T
RANSMIT
P
ULSE
S
HAPER
4.4.1
If the distance between the transmitter and the DSX3 or STSX-1, Cross-Connect system, is less than 225 feet,
enable the Transmit Build Out Circuit by setting the TxLEV_n control bit to “0”. If the distance between the
transmitter and the DSX3 or STSX-1 is greater than 225 feet, disable the Transmit Build Out Circuit.
Guidelines for using Transmit Build Out Circuit
F
IGURE
19. HDB3 E
NCODING
F
ORMAT
0
0
0
0
0
1
1
1
1
1
1
1
V
B
V
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
V
0
0
0
TClk
Line
Signal
TPDATA
TTIP(n)
TRing(n)
1:1
R3
75
TxPOS(n)
TxNEG(n)
TxLineClk(n)
TPData(n)
TNData(n)
TxClk(n)
31.6
+ 1%
31.6
+1%
R1
R2
相關PDF資料
PDF描述
XRT75R12DIB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R12 TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R12IB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75VL00 E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75VL00IV E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
相關代理商/技術參數
參數描述
XRT75R12D_06 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75R12D_07 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75R12DES 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R12DIB 功能描述:網絡控制器與處理器 IC 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75R12DIB-F 功能描述:網絡控制器與處理器 IC 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*