參數資料
型號: XRT75R12D
廠商: Exar Corporation
英文描述: TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述: 第十二章通道E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數: 91/131頁
文件大?。?/td> 717K
代理商: XRT75R12D
PRELIMINARY
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. P1.0.1
86
this SDH signal arrives at the remote PTE, this DS3 or E3 signal will then be extracted from the SDH signal,
and will be output to some other DS3/E3 Terminal Equipment for further processing.
Figure 37 presents an illustration of this approach to transporting DS3 data over a SONET Network
As mentioned above a DS3 or E3 signal will be asynchronously mapped into a SONET or SDH signal and then
transported over the SONET or SDH network. At the remote PTE this DS3 or E3 signal will be extracted (or
de-mapped) from this SONET or SDH signal, where it will then be routed to DS3 or E3 terminal equipment for
further processing.
In order to insure that this "de-mapped" DS3 or E3 signal can be routed to any industry-standard DS3 or E3
terminal equipment, without any complications or adverse effect on the network, the Telcordia and ITU-T
standard committees have specified some limits on both the Intrinsic Jitter and Wander that may exist within
these DS3 or E3 signals as they are de-mapped from SONET/SDH. As a consequence, all PTEs that maps
and de-mapped DS3/E3 signals into/from SONET/SDH must be designed such that the DS3 or E3 data that is
de-mapped from SONET/SDH by these PTEs must meet these Intrinsic Jitter and Wander requirements.
As mentioned above, the LIU can assist the System Designer (of SONET/SDH PTE) by ensuring that their
design will meet these Intrinsic Jitter and Wander requirements.
This section of the data sheet will present the following information to the user.
Some background information on Mapping DS3/E3 signals into SONET/SDH and de-mapping DS3/E3
signals from SONET/SDH.
A brief discussion on the causes of jitter and wander within a DS3 or E3 signal that mapped into a SONET/
SDH signal, and is transported across the SONET/SDH Network.
A brief review of these Intrinsic Jitter and Wander requirements in both SONET and SDH applications.
A brief review on the Intrinsic Jitter and Wander measurement results (of a de-mapped DS3 or E3 signal)
whenever the LIU device is used in a system design.
A detailed discussion on how to design with and configure the LIU device such that the end-system will meet
these Intrinsic Jitter and Wander requirements.
F
IGURE
37. A S
IMPLE
I
LLUSTRATION
OF
A
DS3
SIGNAL
BEING
MAPPED
INTO
AND
TRANSPORTED
OVER
THE
SONET
N
ETWORK
PTE
PTE
SONET
Network
DS3 Data
DS3 Data
相關PDF資料
PDF描述
XRT75R12DIB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75R12 TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R12IB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75VL00 E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75VL00IV E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
相關代理商/技術參數
參數描述
XRT75R12D_06 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75R12D_07 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75R12DES 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R12DIB 功能描述:網絡控制器與處理器 IC 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75R12DIB-F 功能描述:網絡控制器與處理器 IC 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray