- 您現在的位置：買賣IC網 > PDF目錄376462 > XRT8001ID (EXAR CORP) WAN Clock for T1 and E1 Systems PDF資料下載
參數資料
| 型號： | XRT8001ID |
| 廠商： | EXAR CORP |
| 元件分類： | 時鐘及定時 |
| 英文描述： | WAN Clock for T1 and E1 Systems |
| 中文描述： | 8001 SERIES, PLL BASED CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO18 |
| 封裝： | 0.300 INCH, SOIC-18 |
| 文件頁數： | 8/48頁 |
| 文件大小： | 1054K |
| 代理商： | XRT8001ID |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
XRT8001
8
Rev. 1.01
Bits 2 Through 5: The Four (4) Bit Address Values
(Labeled A0, A1, A2 and A3)
The next four rising edges of the SCLK signal will clock
in the 4-bit address value for this particular Read (or
Write) operation. The address selects the Command
Register, within the XRT8001, that the user will either
be reading data from, or writing data to. The user must
supply the address bits to the SDI input pin in ascend-
ing order with the LSB (least significant bit) first.
Bits 6 and 7:
The next two bits, A4 and A5, must be set to “0”, as
shown in Figure 19.
Bit 8 - A6
The value of “A6” is a “don’t care”. Once these first
eight bits have been written into the Microprocessor
Serial Interface, the subsequent action depends upon
whether the current operation is a “Read” or “Write”
operation.
Read Operation
Once the last address bit (A3) has been clocked into
the SDI input, the “Read” operation will proceed through
an idle period, lasting three SCLK periods. On the
falling edge of SCLK Cycle #8 (see Figure 19) the serial
data output signal (SDO) becomes active. At this point
the user can begin reading the data contents of the
addressed Command Register (at Address [A3, A2,
A1, A0]) via the SDO output pin. The Microprocessor
Serial Interface will output this 5-bit data word (D0
through D4) in ascending order (with the LSB first), on
the falling edges of the SCLK pin. As a consequence,
the data (on the SDO output pin) will be sufficiently
stable for reading (by the Microprocessor), on the very
next rising edge of the SCLK pin.
1.0 Operating the Microprocessor Serial
Interface
The XRT8001 Serial Interface is a simple four-wire
interface that is compatible with many of the
microcontrollers available in the market. This interface
consists of the following signals:
CSB
SCLK
SDI
SDO
-
-
-
-
Chip Select (Active Low)
Serial Clock
Serial Data Input
Serial Data Output
Using the Microprocessor Serial Interface
The following instructions, for using the Micropro-
cessor Serial Interface, are best understood by
referring to the diagram in Figure 19.
In order to use the Microprocessor Serial Interface
the user must first provide a clock signal to the
SCLK input pin. Afterwards, the user will initiate a
“Read” or “Write” operation by asserting the “active-
low” Chip Select input pin (CSB). It is important to
assert the CSB pin (e.g., toggle it “l(fā)ow”) at least
50ns prior to the very first rising edge of the clock
signal.
Once the CSB input pin has been asserted, the type of
operation and the target register address must now be
specified by the user. The user provides this informa-
tion to the Microprocessor Serial Interface by writing
eight serial bits of data into the SDI input. Note: each
of these bits will be “clocked” into the SDI input on the
rising edge of SCLK. These eight bits are identified and
described below.
Bit 1 - “R/W” (Read/Write) Bit
This bit will be clocked into the SDI input on the first
rising edge of SCLK (after CSB has been asserted).
This bit indicates whether the current operation is a
“Read” or “Write” operation. A “1” in this bit specifies
a “Read” operation; whereas, a “0” in this bit specifies
a “Write” operation.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT8001IP | WAN Clock for T1 and E1 Systems |
| XRT8010 | 312MHZ CLOCK & CRYSTAL MULTIPLIER WITH LVDS OUTPUTS |
| XRT8010IL | 312MHZ CLOCK & CRYSTAL MULTIPLIER WITH LVDS OUTPUTS |
| XRT8020 | 650 MHZ CLOCK & CRYSTAL MULTIPLIER WITH LVDS OUTPUTS |
| XRT8020IL | 650 MHZ CLOCK & CRYSTAL MULTIPLIER WITH LVDS OUTPUTS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT8001ID-F | 功能描述:鎖相環 - PLL 3.3V-5V temp -45 to 85C RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
| XRT8001ID-F | 制造商:Exar Corporation 功能描述:WAN Clock IC |
| XRT8001IDTR-F | 功能描述:鎖相環 - PLL RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
| XRT8001IP | 制造商:EXAR 制造商全稱:EXAR 功能描述:WAN Clock for T1 and E1 Systems |
| XRT8001IP-F | 功能描述:鎖相環 - PLL RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。