參數資料
型號: XRT83SL314IB-L
廠商: Exar Corporation
文件頁數: 71/83頁
文件大?。?/td> 0K
描述: IC LIU SH T1/E1/J1 14CH 304TBGA
標準包裝: 27
類型: 線路接口裝置(LIU)
驅動器/接收器數: 14/14
規程: T1,E1,J1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 304-LBGA
供應商設備封裝: 304-TBGA(31x31)
包裝: 托盤
xr
XRT83SL314
14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.1
70
CLOCK SELECT REGISTER
The input clock source is used to generate all the necessary clock references internally to the LIU. The
microprocessor timing is derived from a PLL output which is chosen by programming the Clock Select Bits in
register 0xE9h. Therefore, if the clock selection bits are being programmed, the frequency of the PLL output
will be adjusted accordingly. During this adjustment, it is important to "Not" write to any other bit location within
the same register while selecting the input/output clock frequency. For best results, register 0xE9h can be
broken down into two sub-registers with the MSB being bits D[7:4] and the LSB being bits D[3:0] as shown in
Figure 42. Note: Bits D[7:6] are reserved.
FIGURE 42. REGISTER 0XE9H SUB REGISTERS
Programming Examples:
Example 1: Changing bits D[7:4]
If bits D[7:4] are the only values within the register that will change in a WRITE process, the microprocessor
only needs to initiate ONE write operation.
Example 2: Changing bits D[3:0]
If bits D[3:0] are the only values within the register that will change in a WRITE process, the microprocessor
only needs to initiate ONE write operation.
Example 3: Changing bits within the MSB and LSB
In this scenario, one must initiate TWO write operations such that the MSB and LSB do not change within ONE
write cycle. It is recommended that the MSB and LSB be treated as two independent sub-registers. One can
either change the clock selection (LSB) and then change bits D[5:4] (MSB) on the SECOND write, or vice-
versa. No order or sequence is necessary.
TABLE 50: MICROPROCESSOR REGISTER 0XE9H BIT DESCRIPTION
GLOBAL REGISTER (0XE9H)
BIT
NAME
FUNCTION
Register
Type
Default
Value
(HW reset)
D7
Reserved
This Register Bit is Not Used
R/W
0
D6
Reserved
This Register Bit is Not Used
R/W
0
D0
D1
D2
D3
D4
D5
D6
D7
MSB
LSB
Clock Selection Bits
ALLT1/E1, CLKCNTL
相關PDF資料
PDF描述
XRT83SL34IV-F IC LIU T1/E1/J1 QUAD 128TQFP
XRT83SL38IB-F IC LIU SH T1/E1/J1 OCTAL 225BGA
XRT83VL38IB-F IC LIU SH T1/E1/J1 OCTAL 225BGA
XRT83VSH28IB IC LIU SH E1 OCTAL 225BGA
XRT83VSH314IB-F IC LIU SH T1/E1/J1 14CH 304TBGA
相關代理商/技術參數
參數描述
XRT83SL34 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SL34ES 功能描述:外圍驅動器與原件 - PCI 4 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83SL34IV 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT83SL34IV-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT83SL38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR