- 您現在的位置：買賣IC網 > PDF目錄293745 > 1893YI-10 (INTEGRATED DEVICE TECHNOLOGY INC) DATACOM, INTERFACE CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | 1893YI-10 |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 網絡接口 |
| 英文描述： | DATACOM, INTERFACE CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, TQFP-64 |
| 文件頁數： | 73/152頁 |
| 文件大?。?/td> | 943K |
| 代理商： | 1893YI-10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁當前第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁
Chapter 6
Interface Overviews
ICS1893 Rev C 6/6/00
June, 2000
27
ICS1893 - Release
Copyright 2000, Integrated Circuit Systems, Inc.
All rights reserved.
6.2
100M Symbol Interface
The 100M Symbol Interface has a primary objective of supporting 100Base-TX repeater applications for
which the repeater requires only recovered parallel data and for which the repeater provides all the
necessary framing and control functions.
When the ICS1893 MAC/Repeater Interface is configured for 100M Symbol operations, the PHY and the
MAC/repeater exchange unframed 5-bit, parallel symbols at a 25-MHz clock rate.
The configuration functions of the ICS1893 determine the operation of its MAC/Repeater Interface. The
configuration functions are controlled by either input pins (in which case, the HW/SW pin is logic zero to
select the hardware mode) or Management Register bits (in which case, the HW/SW pin is logic one to
select the software mode).
In hardware mode, the ICS1893 enables the 100M Symbol Interface when both of the following are true:
– Its MII/SI input pin is sampled as a logic one (that is, the selection is for the Symbol Interface).
– Its 10/100SEL input pin is sampled as a logic one (that is, the selection is for 100M operations).
In software mode, the ICS1893 enables the 100M Symbol Interface when both the following are true:
– Its MII/SI input pin is sampled as a logic one (that is, the selection is for the Symbol Interface).
– Its Control Register Data Rate bit (bit 0.13) is set to logic one (that is, the selection is for selecting
100M operations)
The 100M Symbol Interface bypasses the ICS1893’s PCS and provides a direct, unscrambled, unframed,
5-bit interface between the MAC/repeater and the PMA sublayer. A benefit of bypassing the PCS is a
reduction in the latency through the PHY. That is, when the ICS1893’s MAC/Repeater Interface is
configured as a 100M Symbol Interface, the bit delays through the PHY are smaller than the standard MII
Data Interface can allow. The ICS1893 provides this 100M Symbol Interface primarily for Repeater
applications, for which latency is a critical performance parameter.
In addition to the exchange of symbol data, an ICS1893 configured for 100M Symbol mode provides
ISO/IEC-compliant control signals (such as CRS) to the MAC/repeater. The ICS1893’s CRS signal
provides a fast look-ahead, which can benefit a repeater application.
In the 100M Symbol Interface mode, the ICS1893 continues to assert the CRS signal using its PCS logic.
This action does not affect the bit delay or latency because the PCS CRS logic examines the bits received
from the PMA sublayer serially. In fact, because the PCS CRS does not wait for a nibble or symbol to be
constructed, the PCS CRS is available in advance of the symbol generation. Therefore, by using the PCS
CRS generation logic, the ICS1893 can provide an ‘early’indication of a Carrier Detect to the
MAC/repeater.
The 100M Symbol Interface consists of the following fourteen signals:
SCRS
SD
SRCLK
SRD[4:0]
STCLK
STD[4:0]
When the ICS1893 MAC/Repeater Interface is configured for 100M Symbol operations, its default MII pin
names and their associated functions are redefined. For more information, see Section 9.3.4.2,
“MAC/Repeater Interface Pins for 100M Symbol Interface”.
相關PDF資料 |
PDF描述 |
|---|---|
| 1894-40KLF | DATACOM, INTERFACE CIRCUIT, QCC40 |
| 1894-40KLFT | DATACOM, INTERFACE CIRCUIT, QCC40 |
| 1895230000 | 15 A, STRIP TERMINAL BLOCK, 2 ROWS, 2 DECKS |
| 18F-08P-241 | 8 CONTACT(S), CABLE MOUNT, MINI DIN CONNECTOR, PLUG |
| 18F-08P-244 | 8 CONTACT(S), CABLE MOUNT, MINI DIN CONNECTOR, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1893YI-10LF | 功能描述:以太網 IC 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 1893YI-10LFT | 功能描述:以太網 IC 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 1894 | 功能描述:支架與墊片 HEX .187X.625 ALUM RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
| 1894# | 制造商:Fluke Electronics 功能描述:BNC (F)/BANANA PLUG 制造商:Pomona Electronics 功能描述: |
| 1894 | 制造商:Pomona Electronics 功能描述:ADAPTER BNC FEMALE-BANANA PLUG 制造商:Pomona Electronics 功能描述:ADAPTER, BNC FEMALE-BANANA PLUG |
發布緊急采購，3分鐘左右您將得到回復。