參數資料
型號： 24C01SC
廠商： Microchip Technology Inc.
英文描述： 1K 5.0V IIC serial EEPROMs(2.5V~5.5V,1K位,1M次擦寫周期,ISO7816標準)
中文描述： 一千5.0V國際進口電壓（2.5V?5.5V的，每1000位，100萬次擦寫周期，符合ISO7816標準串行EEPROM）
文件頁數： 49/170頁
文件大?。?/td> 4191K
代理商： 24C01SC
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 47
PIC16F62X
7.1
Timer1 Operation in Timer Mode
Timer mode is selected by clearing the TMR1CS
(T1CON<1>) bit. In this mode, the input clock to the
timer is F
OSC
/4. The synchronize control bit T1SYNC
(T1CON<2>) has no effect since the internal clock is
always in sync.
7.2
Timer1 Operation in Synchronized
Counter Mode
Counter mode is selected by setting bit TMR1CS. In
this mode the timer increments on every rising edge of
clock input on pin RB7/T1OSI when bit T1OSCEN is
set or pin RB6/T1OSO/T1CKI when bit T1OSCEN is
cleared.
If T1SYNC is cleared, then the external clock input is
synchronized with internal phase clocks. The synchro-
nization is done after the prescaler stage. The
prescaler stage is an asynchronous ripple-counter.
In this configuration, during SLEEP mode, Timer1 will
not increment even if the external clock is present,
since the synchronization circuit is shut off. The
prescaler however will continue to increment.
7.2.1
EXTERNAL CLOCK INPUT TIMING
FOR SYNCHRONIZED COUNTER
MODE
When an external clock input is used for Timer1 in
Synchronized Counter mode, it must meet certain
requirements. The external clock requirement is due to
internal phase clock (Tosc) synchronization. Also, there
is a delay in the actual incrementing of TMR1 after
synchronization.
When the prescaler is 1:1, the external clock input is
the same as the prescaler output. The synchronization
of T1CKI with the internal phase clocks is accom-
plished by sampling the prescaler output on the Q2 and
Q4 cycles of the internal phase clocks. Therefore, it is
necessary for T1CKI to be high for at least 2Tosc (and
a small RC delay of 20 ns) and low for at least 2Tosc
(and a small RC delay of 20 ns). Refer to the appropri-
ate electrical specifications, parameters 45, 46, and 47.
When a prescaler other than 1:1 is used, the external
clock input is divided by the asynchronous ripple-
counter type prescaler so that the prescaler output is
symmetrical. In order for the external clock to meet the
sampling requirement, the ripple-counter must be
taken into account. Therefore, it is necessary for T1CKI
to have a period of at least 4Tosc (and a small RC delay
of 40 ns) divided by the prescaler value. The only
requirement on T1CKI high and low time is that they do
not violate the minimum pulse width requirements of 10
ns). Refer to the appropriate electrical specifications,
parameters 40, 42, 45, 46, and 47.
FIGURE 7-1:
TIMER1 BLOCK DIAGRAM
TMR1H
TMR1L
T1OSC
T1SYNC
TMR1CS
T1CKPS1:T1CKPS0
SLEEP Input
T1OSCEN
Enable
Oscillator(1)
F
OSC
/4
Internal
Clock
TMR1ON
Prescaler
1, 2, 4, 8
Synchronize
det
1
0
0
1
Synchronized
Clock Input
2
RB6/T1OSO/T1CKI
RB7/T1OSI
Note
1:
When the T1OSCEN bit is cleared, the inverter and feedback resistor are turned off. This eliminates power drain.
Set flag bit
TMR1IF on
Overflow
TMR1
相關PDF資料
PDF描述
24C02SC 2K 5.0V IIC serial EEPROMs(2.5V~5.5V,2K位,1M次擦寫周期,ISO7816標準)
24C02A 2K 5.0V CMOS serial EEPROMs(2K位,5.0V,IIC串行EEPROM)
24C02C 2K 5.0V IIC serial EEPROMs(2K位，1M次擦寫周期，硬件寫保護，二線串行接口,EEPROM)
24C02C-EP 2K 5.0V I 2 C ⑩ Serial EEPROM
24C02C-ESN 2K 5.0V I 2 C ⑩ Serial EEPROM
相關代理商/技術參數
參數描述
24C01SC/S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|128X8|CMOS|DIE
24C01SC-/S 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C Serial EEPROMs for Smart Cards
24C01SC/S08 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|128X8|CMOS|DIE
24C01SC-/S08 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C Serial EEPROMs for Smart Cards
24C01SC/W 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|128X8|CMOS|WAFER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*