參數資料
型號： 73M1866B-KEYCHN
廠商： Maxim Integrated Products
文件頁數： 68/88頁
文件大?。?/td> 0K
描述： BOARD KEYCHAIN INF DANUBE EVM
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
73M1866B/73M1966B Data Sheet
DS_1x66B_001
70
Rev. 1.6
Function
Mnemonic
Register
Location
Type
Description
ENLVD
0x12[3]
WO
LeV Detection (OVDET, UVDET, OIDET monitors)
0 = Enable LeV detection. (Default)
1 = Disable LeV detection (used in line-powered mode to save power).
This bit will be 0 when Line Powered Mode is detected (ENLPW is set
in Register 0x02[2]) and set to 1 when an interrupt occurs within the
73M1916. This bit must be reset prior to switching back to Barrier
Powered Mode.
ENNOM
0x12[0]
WO
Enable Nominal Operation
0 = Speeds up the on and off hook transitions time by increasing the
DC loop bandwidth of the DC transconductance circuit in the
73M1x66B. This should be used for pulse dialing, going on and off
hook, etc. In addition, ENNOM=0 prevents the reset of all bits in
Register 0x12. (Default)
1 = Enter Nominal Operation. Reduces the loop bandwidth of the DC
transconductance circuit. Allows reset of Register 0x12 caused by bits
UVDET, OVDET or OIDET.
ENSHL
0x12[4]
WO
Enable Shunt Loading
0 = Disable shunt loading. (Default)
1 = Enable shunt loading of the line. Not used for most applications.
IDISPD
0x13[1]
WO
Discharge and Pulse Dialing
Controls the DC discharge current and how fast the loop turns off.
Affects pulse dialing waveform. Controls the amount of discharge
current during hook switch transitions.
0 = Minimum current. (Default)
1 = Maximum current.
It is recommended to set IDISPD to 1 prior to hook switching
operations.
ILM
0x13[5]
WO
Current Limit Enable
This control enables or disables loop current limit.
0 = No current limit. (Default)
1 = 42 mA current limit enabled.
ILMON
0x1E[7]
R
Current Limit Mode On
This status bit is effective only when the ILM bit is set to 1.
0 = Loop current is lower than 42 mA.
1 = Loop current is higher than 42 mA and the current limiting mode is
active.
OFH
0x12[7]
WO
Off-Hook Enable
This bit controls the state of the Hook signal.
0 = On-Hook. (Default)
1 = Off-Hook.
PLDM
0x13[3]
WO
Pulse Dialing Mode Enable
Alleviates the strict timing requirements for the Host having to control
ENDC and OFH during pulse dialing. With PLDM = 1, the Host only
has to toggle OFH to perform pulse dialing.
0 = Pulse Dialing Mode is disabled. (Default)
1 = Pulse Dialing Mode is enabled.
RLPNEN
0x16[5]
W
Receive Low Pass Notch Enable
0 = Billing Tone Receive Low Pass Notch (RLPN) filter bypassed.
(Default)
1 = RLPN Filter Enabled. See RLPNH for notch frequency selection.
相關PDF資料
PDF描述
UPS2D221MRD6 CAP ALUM 220UF 200V 20% RADIAL
73M1822-KEYCHN BOARD KEYCHAIN 73M1822 42-QFN
78Q2133-DB EVAL BOARD 78Q2133
MAX14821EVKIT# EVAL KIT MAX14821
UVZ1C472MHD CAP ALUM 4700UF 16V 20% RADIAL
相關代理商/技術參數
參數描述
73M1902-IM/F 功能描述:電信線路管理 IC MicroDAA Chip Set Host Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
73M1902-IMR/F 功能描述:電信線路管理 IC MicroDAA Chip Set Host Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
73M1902-IVT/F 功能描述:電信線路管理 IC MicroDAA Chip Set Host Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
73M1902-IVTR/F 功能描述:電信線路管理 IC MicroDAA Chip Set Host Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
73M1903 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Soft Modem AFEs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*