參數資料
型號： AD9148-M5372-EBZ
廠商： Analog Devices Inc
文件頁數： 63/72頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD9149, ADL5372
設計資源： AD9148-M5372-EBZ Schematic
AD9148-M5372-EBZ BOM
AD9148-M5372-EBZ Gerber Files
標準包裝： 1
系列： *
AD9148
Data Sheet
Rev. B | Page 66 of 72
INTERRUPT REQUEST OPERATION
The AD9148 provides an interrupt request output signal
(Pin H4, IRQ) that can be used to notify an external host
processor of significant device events. Upon assertion of the
interrupt, the device should be queried to determine the precise
event that occurred. The IRQ pin is an open-drain, active low
output.
Pull the IRQ pin high external to the device. This pin may be
tied to the interrupt pins of other devices with open-drain outputs
to wired-OR these pins together.
Ten different event flags provide visibility into the device. These
10 flags are located in the two event flag registers (Register 0x06
and Register 0x07). The behavior of each of the event flags is
independently selected in the interrupt enable registers
(Register 0x04 and Register 0x05). When the flag interrupt
enable is active, the event flag latches and triggers an external
interrupt. When the flag interrupt is disabled, the event flag
simply monitors the source signal, and the external IRQ
remains inactive.
Figure 91 shows the IRQ-related circuitry. Figure 91 shows how the
event flag signals propagate to the IRQ output. The interupt_enable
signal represents one bit from the interrupt enable register. The
event_flag signal represents one bit from the event flag register.
The event_flag_source signal represents one of the device signals
that can be monitored such as the PLL_locked signal from the
PLL phase detector or the FIFO Warning 1 signal from the
FIFO controller.
When an interrupt enable bit is set high, the corresponding event
flag bit reflects a positively tripped (that is, latched on the rising
edge of the event_flag_source version of the event_flag_source signal.
This signal also asserts the external IRQ. When an interrupt enable
bit is set low, the event flag bit reflects the current status of the
event_flag_source signal, and the event flag has no effect on the
external IRQ.
The latched version of an event flag (the interupt_source signal)
can be cleared in two ways. The recommended way is by writing 1
to the corresponding event flag bit. A hardware or software reset
also clears the interupt_source.
INTERRUPT SERVICE ROUTINE
Interrupt request management starts by selecting the set of event
flags that require host intervention or monitoring. Those events
that require host action should be enabled so that the host is
notified when they occur. For events requiring host intervention,
upon IRQ activation, run the following routine to clear an
interrupt request:
Read the status of the event flag bits that are being
monitored.
Set the interupt enable bit low so that the unlatched
event_flag_source can be monitored directly.
Perform any actions that may be required to quiet the
event_source_flag. In many cases, no specific actions may
be required.
Read the event flag to verify that the actions taken have
quieted the event_flag_source.
Clear the interrupt by writing 1 to the event flag bit.
Set the interrupt enable bits of the events to be monitored.
Noted that some of the event_flag_source signals are latched
signals. These are cleared by writing to the corresponding event
flag bit. Details of each of the event flags can be found in Table 12.
INTERRUPT_ENABLE
EVENT_FLAG_SOURCE
DEVICE_RESET
EVENT_FLAG
INTERRUPT
SOURCE
1
0
OTHER
INTERRUPT
SOURCES
IRQ
WRITE_1_TO_EVENT_FLAG
08910-
088
Figure 91. Simplified Schematic of IRQ Circuitry
相關PDF資料
PDF描述
AD9737A-EBZ BOARD EVAL FOR AD9737A
MIC2026-1YM IC DISTRIBUTION SW DUAL 8-SOIC
VI-B1L-EY CONVERTER MOD DC/DC 28V 50W
AD9706-DPG2-EBZ BOARD EVAL FOR AD9706
AD9705-DPG2-EBZ BOARD EVAL FOR AD9705
相關代理商/技術參數
參數描述
AD9148-M5375-EBZ 功能描述:BOARD EVAL FOR AD9149, ADL5375 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
AD9152BCPZ 功能描述:16 Bit Digital to Analog Converter 2 56-LFCSP-WQ (8x8) 制造商:analog devices inc. 系列:TxDAC+? 包裝:托盤 零件狀態:有效 位數:16 數模轉換器數:2 建立時間:- 輸出類型:Current - Unbuffered 差分輸出:是 數據接口:JESD204B 參考類型:內部 電壓 - 電源，模擬:3.13 V ~ 3.47 V 電壓 - 電源，數字:1.14 V ~ 1.26 V INL/DNL（LSB）:±10，±5 架構:電流源 工作溫度:-40°C ~ 85°C 封裝/外殼:56-WFQFN 裸焊盤，CSP 供應商器件封裝:56-LFCSP-WQ（8x8） 標準包裝:1
AD9152BCPZRL 功能描述:16 Bit Digital to Analog Converter 2 56-LFCSP-WQ (8x8) 制造商:analog devices inc. 系列:TxDAC+? 包裝:帶卷（TR） 零件狀態:有效 位數:16 數模轉換器數:2 建立時間:- 輸出類型:Current - Unbuffered 差分輸出:是 數據接口:JESD204B 參考類型:內部 電壓 - 電源，模擬:3.13 V ~ 3.47 V 電壓 - 電源，數字:1.14 V ~ 1.26 V INL/DNL（LSB）:±10，±5 架構:電流源 工作溫度:-40°C ~ 85°C 封裝/外殼:56-WFQFN 裸焊盤，CSP 供應商器件封裝:56-LFCSP-WQ（8x8） 標準包裝:2,500
AD9152-EBZ 功能描述:AD9152 TxDAC+? Series 16 Bit 2.25G Samples Per Second Digital to Analog Converter (DAC) Evaluation Board 制造商:analog devices inc. 系列:TxDAC+? 零件狀態:有效 DAC 數:2 位數:16 采樣率（每秒）:2.25G 數據接口:SPI 建立時間:- DAC 類型:電流 工作溫度:-40°C ~ 85°C 所含物品:板，線纜 使用的 IC/零件:AD9152 標準包裝:1
AD9152-FMC-EBZ 功能描述:AD9152 TxDAC+? Series 16 Bit 2.25G Samples Per Second Digital to Analog Converter (DAC) Evaluation Board 制造商:analog devices inc. 系列:TxDAC+? 零件狀態:有效 DAC 數:2 位數:16 采樣率（每秒）:2.25G 數據接口:SPI 建立時間:- DAC 類型:電流 工作溫度:-40°C ~ 85°C 所含物品:板，線纜 使用的 IC/零件:AD9152 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*