參數資料
型號： ADAV803ASTZ-REEL
廠商： Analog Devices Inc
文件頁數： 19/60頁
文件大小： 0K
描述： IC CODEC AUDIO R-DVD 3.3V 64LQFP
標準包裝： 1,500
類型： 音頻編解碼器
數據接口： 串行
分辨率（位）： 24 b
ADC / DAC 數量： 2 / 2
三角積分調變： 無
動態范圍，標準 ADC / DAC (db)： 102 / 101
電壓 - 電源，模擬： 3 V ~ 3.6 V
電壓 - 電源，數字： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 帶卷 (TR)
配用： EVAL-ADAV803EBZ-ND - BOARD EVALUATION FOR ADAV803
ADAV803
Rev. A | Page 26 of 60
The size of the user bit buffer can be set by programming the
RxBCONF0 bit in the receiver buffer configuration register, as
shown in Table 11.
Table 11. RxBCONF3 Functionality
RxBCONF0
Receiver User Bit Buffer Size
0
384 bits with Preamble Z as the start of the block.
1
768 bits with Preamble Z as the start of the block.
The updating of the user bit buffer is controlled by Bits
RxBCONF[2:1] and Bit 7 to Bit 4 of the channel status register,
as shown in Table 12 and Table 13.
Table 12. RxBCONF[2:1] Functionality
RxBCONF
Bit 2
Bit 1
Receiver User Bit Buffer Configuration
0
User bits are ignored.
0
1
Update second buffer when first buffer is full.
1
0
Format according to Byte 1, Bit 4 to Bit 7, if
PRO bit is set. Format according to IEC60958-3,
if PRO bit is clear.
Table 13. Automatic User Bit Configuration
Bits
7
6
5
4
Automatic Receiver User Bit Buffer
Configuration
0
User bits are ignored.
0
1
0
AES-18 format: the user bit buffer is treated in
the same way as when RxBCONF[2:1] = 0b01.
1
0
User bit buffer is updated in the same way as
when RxBCONF[2:1] = 0b01 and RxBCONF0 =
0b00.
1
0
User-defined format: the user bit buffer is
treated in the same way as when
RxBCONF[2:1] = 0b01.
When the user bit buffer has been filled, the RxUBINT
interrupt bit in the interrupt status register is set, provided that
the RxUBINT mask bit is set, to indicate that the buffer has new
information and can be read.
For the special case when the user data is formatted according
to the IEC 60958-3 standard into messages made of information
units, called IUs, the zeros stuffed between each IU and each
message are removed and only the IUs are stored. Once the end
of the message is sensed by more that eight zeros between IUs,
the user bit buffer is updated with the complete message and
the first buffer begins looking for the start of the next message.
Each IU is stored as a byte consisting of 1, Q, R, S, T, U, V, and
W bits (see the IEC 60958-3 specification for more
information). When 96 IUs are received, the Q subcode of the
IUs is stored in the Q subcode buffer, consisting of 10 bytes. The
Q subcode is the Q bits taken from each of the 96 IUs. The first
10 bytes (80 bits) of the Q subcode contain information sent by
CD, MD, and DAT systems. The last 16 bits of the Q subcode
are used to perform a CRC check of the Q subcode. If an error
occurs in the CRC check of the Q subcode, the QCRCERROR
bit is set. This is a sticky bit that remains high until the register
is read.
Transmitter Operation
The S/PDIF transmitter has a similar buffer structure to the
receive section. The transmitter channel status buffer occupies
24 bytes of the register map. This buffer is long enough to store
the 192 bits required for one channel of channel status informa-
tion. Setting the TxCSSWITCH bit determines if the data
loaded to the transmitter channel status buffer is intended for
Channel A or Channel B. In most cases, the channel status bits
for Channel A and Channel B are the same, in which case
setting the Tx_A/B_Same bit reads the data from the trans-
mitter channel status buffer and transmits it on both channels.
Because the channel status information is rarely changed during
transmission, the information contained in the buffer is
transmitted repeatedly. The Disable_Tx_Copy bit can be used
to prevent the channel status bits from being copied from the
transmitter CS buffer into the S/PDIF transmitter buffer until
the user has finished loading the buffers. This feature is
typically used, if the Channel A data and Channel B data are
different. Setting the bit prevents the data from being copied.
Clearing the bit allows the data to be copied and then
transmitted. Figure 48 shows how the buffers are organized.
04
75
6-
0
48
TxCSSWITCH
TRANSMIT
CS BUFFER
(0x38 TO 0x4F)
CHANNEL
STATUS A
(24 × 8 BITS)
CHANNEL
STATUS B
(24 × 8 BITS)
DITOUT
S/PDIF
TRANSMIT
BUFFER
Figure 48. Transmitter Channel Status Buffer
As with the receiver section, the transmitted user bits are also
double-buffered. This is required because, unlike the channel
status bits, the user bits do not necessarily repeat themselves.
The user bits can be buffered in various configurations, as listed
in Table 14. Transmission of the user bits is determined by the
state of the BCONF3 bit. If the bit is 0, the user bits begin
transmitting right away without alignment to the Z preamble. If
this bit is 1, the user bits do not start transmitting until a
Z preamble occurs when the TxBCONF[2:1] bits are 01.
Table 14. Transmitter User Bit Buffer Configurations
TxBCONF2-1
Bit 2
Bit 1
Transmitter User Bit Buffer Configuration
0
Zeros are transmitted for the user bits.
0
1
Host writes user bits to the buffer until it is full.
1
0
Writes the user bits to the buffer in IUs
specified by IEC60958-3 and transmits them
according to the standard.
1
First 10 bytes of the user-bit buffer are
configured to store a Q subcode.
相關PDF資料
PDF描述
AD1939YSTZRL IC CODEC 24BIT ADC/DAC 64-LQFP
AD1937WBSTZ-RL IC CODEC 4/ADC DIFF OUT 64-LQFP
AD1938WBSTZ-RL IC CODEC 24BIT 4ADC/8DAC 48LQFP
AD1938YSTZRL IC CODEC 24BIT 4ADC/8DAC 48LQFP
MCF5213LCVM80 IC MCU 256K FLASH 80MHZ 81MAPBGA
相關代理商/技術參數
參數描述
ADAV804AST 制造商:Analog Devices 功能描述:AUDIO CODEC FOR RECORDABLE DVD - Bulk
ADAV804ASTZ 制造商:Analog Devices 功能描述:
ADB.1X40 制造商:FACOM 功能描述:SCREWDRIVER STUB POZI NO.1 制造商:FACOM 功能描述:SCREWDRIVER, STUB, POZI NO.1 制造商:FACOM 功能描述:SCREWDRIVER, STUB, POZI NO.1; Overall Length:90mm; Blade Length:40mm; SVHC:No SVHC (19-Dec-2012); Range:PZ1; Screwdriver Type:Pozi; Tip / Nozzle Size:PZ1; Tip / Nozzle Style:Pozidriv ;RoHS Compliant: NA
ADB0039 制造商:AVOCENT 功能描述:Cyclades - Crossover adapter - RJ-45 (M) - RJ-45 (F)
ADB-1 制造商:IDEC CORPORATION 功能描述:LACHING BEAM ATTACH
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*