參數資料
型號: AM79C978AVCW
廠商: ADVANCED MICRO DEVICES INC
元件分類: 微控制器/微處理器
英文描述: Single-Chip 1/10 Mbps PCI Home Networking Controller
中文描述: 5 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP144
封裝: TQFP-144
文件頁數: 67/256頁
文件大小: 3505K
代理商: AM79C978AVCW
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁
Am79C978A
67
Transmit FCS Generation
Automatic generation and transmission of FCS for a
transmit frame depends on the value of DXMTFCS
(CSR15, bit 3). If DXMTFCS is cleared to 0, the trans-
mitter will generate and append the FCS to the trans-
mitted frame. If the automatic padding feature is
invoked (APAD_XMT is set in CSR4), the FCS will be
appended by theAm79C978A controller regardless of
the state of DXMTFCS or ADD_FCS (TMD1, bit 29).
Note that the calculated FCS is transmitted most signif-
icant bit first. The default value of DXMTFCS is 0 after
H_RESET.
ADD_FCS (TMD1, bit 29) allows the automatic gener-
ation and transmission of FCS on a frame-by-frame
basis. DXMTFCS should be cleared to 0 in this mode.
To generate FCS for a frame, ADD_FCS must be set in
all descriptors of a frame (STP is set to 1). Note that bit
29 of TMD1 has the function of ADD_FCS if SWSTYLE
(BCR20, bits 7-0) is programmed to 0, 2, or 3.
Transmit Exception Conditions
Exception conditions for frame transmission fall into
two distinct categories: those conditions which are
the result of normal network operation, and those
which occur due to abnormal network and/or host re-
lated events.
Normal events which may occur and which are handled
autonomously by the Am79C978A controller include
collisions within the slot time with automatic retry. The
Am79C978A controller will ensure that collisions which
occur within 512 bit times from the start of transmission
(including preamble) will be automatically retried with
no host intervention. The transmit FIFO ensures this by
guaranteeing that data contained within the FIFO will
not be overwritten until at least 64 bytes (512 bits) of
preamble plus address, length, and data fields have
been transmitted onto the network without encounter-
ing a collision. Note that if DRTY (CSR15, bit 5) is set
to 1 or if the network interface is operating in full-duplex
mode, no collision handling is required, and any byte of
frame data in the FIFO can be overwritten as soon as
it is transmitted.
If 16 total attempts (initial attempt plus 15 retries)
fail, the Am79C978A controller sets the RTRY bit in
the current transmit TDTE in host memory (TMD2),
gives up ownership (resets the OWN bit to 0) for
this frame, and processes the next frame in the
transmit ring for transmission.
Abnormal network conditions include:
Loss of carrier
Late collision
SQE Test Error (does not apply to 100 Mbps networks.)
These conditions should not occur on a correctly con-
figured IEEE 802.3 network operating in half-duplex
mode. If they do, they will be reported. None of these
conditions will occur on a network operating in full-
duplex mode. (See the section on
Full-Duplex Opera-
tion
for more detail.)
When an error occurs in the middle of a multi-buffer
frame transmission, the error status will be written in the
current descriptor. The OWN bit(s) in the subsequent
descriptor(s) will be cleared until the STP (the next
frame) is found.
Loss of Carrier
LCAR will be reported for every frame transmitted if the
Am79C978A controller detects a loss of carrier.
Late Collision
A late collision will be reported if a collision condition oc-
curs after one slot time (512 bit times) after the transmit
process was initiated (first bit of preamble commenced).
The Am79C978A controller will abandon the transmit
process for that frame, set Late Collision (LCOL) in the
associated TMD2, and process the next transmit frame
in the ring. Frames experiencing a late collision will not
be retried. Recovery from this condition must be per-
formed by upper layer software.
SQE Test Error
If the network port is in Link Fail state, CERR will be
asserted in the 10BASE-T mode after transmit. CERR
will never cause INTA to be activated. It will, however,
set the ERR bit CSR0.
Receive Operation
The receive operation and features of the Am79C978A
controller are controlled by programmable options. The
Am79C978A controller offers a large receive FIFO to
provide frame buffering for increased system latency,
automatic flushing of collision fragments (runt packets),
automatic receive pad stripping, and a variety of ad-
dress match options.
Receive Function Programming
Automatic pad field stripping is enabled by setting the
ASTRP_RCV bit in CSR4. This can provide flexibility
in the reception of messages using the IEEE 802.3
frame format.
All receive frames can be accepted by setting the
PROM bit in CSR15. Acceptance of unicast and
broadcast frames can be individually turned off by
setting the DRCVPA or DRCVBC bits in CSR15.
The Physical Address register (CSR12 to CSR14)
stores the address that theAm79C978A controller
compares to the destination address of the incom-
ing frame for a unicast address match. The Logical
Address Filter register (CSR8 to CSR11) serves as
a hash filter for multicast address match.
相關PDF資料
PDF描述
AM79C978 Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C981 Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C981JC Integrated Multiport Repeater Plus⑩ (IMR+⑩)
AM79C982 basic Integrated Multiport Repeater (bIMR)
AM79C982-4JC basic Integrated Multiport Repeater (bIMR)
相關代理商/技術參數
參數描述
AM79C978KC/W 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C978VC/W 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip 1/10 Mbps PCI Home Networking Controller
AM79C979BKC\\W 制造商:Advanced Micro Devices 功能描述:
AM79C98 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Twisted-Pair Ethernet Transceiver (TPEX)