參數資料
型號： C8051F010-TB
廠商： Silicon Laboratories Inc
文件頁數： 108/171頁
文件大?。?/td> 0K
描述： BOARD PROTOTYPING W/C8051F010
標準包裝： 1
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
6.2.
ADC Modes of Operation
The ADC uses VREF to determine its full-scale voltage, thus the reference must be properly configured before
performing a conversion (see Section 9). The ADC has a maximum conversion speed of 100ksps. The ADC
conversion clock is derived from the system clock. Conversion clock speed can be reduced by a factor of 2, 4, 8 or
16 via the ADCSC bits in the ADC0CF Register. This is useful to adjust conversion speed to accommodate
different system clock speeds.
A conversion can be initiated in one of four ways, depending on the programmed states of the ADC Start of
Conversion Mode bits (ADSTM1, ADSTM0) in ADC0CN. Conversions may be initiated by:
1.
Writing a 1 to the ADBUSY bit of ADC0CN;
2.
A Timer 3 overflow (i.e. timed continuous conversions);
3.
A rising edge detected on the external ADC convert start signal, CNVSTR;
4.
A Timer 2 overflow (i.e. timed continuous conversions).
Writing a 1 to ADBUSY provides software control of the ADC whereby conversions are performed “on-demand”.
During conversion, the ADBUSY bit is set to 1 and restored to 0 when conversion is complete. The falling edge of
ADBUSY triggers an interrupt (when enabled) and sets the ADCINT interrupt flag. Note: When conversions are
performed “on-demand”, the ADCINT flag, not ADBUSY, should be polled to determine when the
conversion has completed. Converted data is available in the ADC data word MSB and LSB registers, ADC0H,
ADC0L. Converted data can be either left or right justified in the ADC0H:ADC0L register pair (see example in
Figure 6.9) depending on the programmed state of the ADLJST bit in the ADC0CN register.
The ADCTM bit in register ADC0CN controls the ADC track-and-hold mode. In its default state, the ADC input is
continuously tracked, except when a conversion is in progress. Setting ADCTM to 1 allows one of four different
low power track-and-hold modes to be specified by states of the ADSTM1-0 bits (also in ADC0CN):
1.
Tracking begins with a write of 1 to ADBUSY and lasts for 3 SAR clocks;
2.
Tracking starts with an overflow of Timer 3 and lasts for 3 SAR clocks;
3.
Tracking is active only when the CNVSTR input is low;
4.
Tracking starts with an overflow of Timer 2 and lasts for 3 SAR clocks.
Modes 1, 2 and 4 (above) are useful when the start of conversion is triggered with a software command or when the
ADC is operated continuously. Mode 3 is used when the start of conversion is triggered by external hardware. In
this case, the track-and-hold is in its low power mode at times when the CNVSTR input is high. Tracking can also
be disabled (shutdown) when the entire chip is in low power standby or sleep modes.
Figure 6.2. 10-Bit ADC Track and Conversion Example Timing
12
345
678
9
10 11 12 13 14 15 16
CNVSTR
(ADSTM[1:0]=10)
ADCTM=1
Track
Convert
Low Power Mode
ADCTM=0
Track Or Convert
Convert
Track
Low Power or
Convert
Timer2, Timer3 Overflow;
Write 1 to ADBUSY
(ADSTM[1:0]=00, 01, 11)
ADCTM=1
Track
Convert
Low Power Mode
ADCTM=0
Track or Convert
Convert
Track
Low Power or
Convert
A. ADC Timing for External Trigger Source
B. ADC Timing for Internal Trigger Sources
SAR Clocks
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
SAR Clocks
41
Rev. 1.7
相關PDF資料
PDF描述
ISC1210ER3R3J INDUCTOR WW 3.3UH 5% 1210
RP15-4812DF/P-HC CONV DC/DC 15W 36-75VIN +/-12V
ISC1210ER2R7J INDUCTOR WW 2.7UH 5% 1210
ISC1210ER2R2J INDUCTOR WW 2.2UH 5% 1210
GSM06DRKF CONN EDGECARD 12POS DIP .156 SLD
相關代理商/技術參數
參數描述
C8051F011 功能描述:8位微控制器 -MCU 32KB 10ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F011-GQ 功能描述:8位微控制器 -MCU 32KB 10ADC 48P MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F011-GQR 功能描述:8位微控制器 -MCU 32KB 10ADC 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F011R 功能描述:8位微控制器 -MCU C 10Bit 48Pin RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F012 功能描述:8位微控制器 -MCU 32KB 10ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*