參數資料
型號： CDB4392
廠商： Cirrus Logic Inc
文件頁數： 6/40頁
文件大小： 0K
描述： EVALUATION BOARD FOR CS4392
標準包裝： 1
DAC 的數量： 2
位數： 24
采樣率（每秒）： 192k
數據接口： 串行
DAC 型： 電壓
工作溫度： -10°C ~ 70°C
已供物品： 板
已用 IC / 零件： CS4392
相關產品： 598-1065-5-ND - IC DAC 24BIT 192KHZ W/VC 20TSSOP
CS4392
14
DS459PP3
4. CONTROL PORT INTERFACE
The control port is used to load all the internal register settings (see section 6). The operation of the control
port may be completely asynchronous with the audio sample rate. However, to avoid potential interference
problems, the control port pins should remain static if no operation is required.
The control port operates in one of two modes: I2C
or SPI.
Notes: MCLK must be applied during all I2C communication.
4.0.1
MAP Auto Increment
The device has MAP (memory address pointer) auto increment capability enabled by the INCR bit
(also the MSB) of the MAP. If INCR is set to 0, MAP will stay constant for successive I2C writes
or reads, and SPI writes. If INCR is set to 1, MAP will auto increment after each byte is written,
allowing block reads or writes of successive registers.
4.0.2
I2C Mode
In the I2C mode, data is clocked into and out of the bi-directional serial control data line, SDA, by
the serial control port clock, SCL (see Figure 8 for the clock to data relationship). There is no CS
pin. Pin AD0 enables the user to alter the chip address (001000[AD0][R/W]) and should be tied to
VL or AGND as required, before powering up the device. If the device ever detects a high to low
transition on the AD0/CS pin after power-up, SPI mode will be selected.
4.0.2a
I2C Write
To write to the device, follow the procedure below while adhering to the control port
Switching Specifications in section 7.
1) Initiate a START condition to the I2C bus followed by the address byte. The upper 6 bits
must be 001000. The seventh bit must match the setting of the AD0 pin, and the eighth must
be 0. The eighth bit of the address byte is the R/W bit.
2) Wait for an acknowledge (ACK) from the part, then write to the memory address pointer,
MAP. This byte points to the register to be written.
3) Wait for an acknowledge (ACK) from the part, then write the desired data to the register
pointed to by the MAP.
4) If the INCR bit (see section 4.0.1) is set to 1, repeat the previous step until all the desired
registers are written, then initiate a STOP condition to the bus.
5) If the INCR bit is set to 0 and further I2C writes to other registers are desired, it is nec-
essary to initiate a repeated START condition and follow the procedure detailed from step
1. If no further writes to other registers are desired, initiate a STOP condition to the bus.
相關PDF資料
PDF描述
0210490185 CABLE JUMPER 1.25MM .254M 12POS
RPP20-1215D/N CONV DC/DC 20W 9-18VIN +/-15VOUT
SDR0604-220YL INDUCTOR POWER 22UH 1.10A SMD
EBA22DTKD-S288 CONN EDGECARD 44POS .125 EXTEND
380LX562M035H022 CAP ALUM 5600UF 35V 20% SNAP
相關代理商/技術參數
參數描述
CDB4396 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:24-Bit, 192 kHz D/A Converter for Digital Audio
CDB4397 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:24-Bit, Multi-Standard D/A Converter for Digital Audio
CDB4398 功能描述:音頻 IC 開發工具 Eval Bd RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB43L21 功能描述:音頻 IC 開發工具 Eval Bd 98dB 96kHz Low-Pwr DAC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB43L22 功能描述:音頻 IC 開發工具 Eval Bd LP DAC w/ClassD Spkr Driver RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*