- 您現在的位置：買賣IC網 > PDF目錄17058 > CDB4392 (Cirrus Logic Inc)EVALUATION BOARD FOR CS4392 PDF資料下載
參數資料
| 型號： | CDB4392 |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 8/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION BOARD FOR CS4392 |
| 標準包裝： | 1 |
| DAC 的數量： | 2 |
| 位數： | 24 |
| 采樣率（每秒）： | 192k |
| 數據接口： | 串行 |
| DAC 型： | 電壓 |
| 工作溫度： | -10°C ~ 70°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | CS4392 |
| 相關產品： | 598-1065-5-ND - IC DAC 24BIT 192KHZ W/VC 20TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
CS4392
16
DS459PP3
4.0.3
SPI Mode
In SPI mode, data is clocked into the serial control data line, CDIN, by the serial control port clock,
CCLK (see Figure 9 for the clock to data relationship). There is no AD0 pin. Pin CS is the chip
select signal and is used to control SPI writes to the control port. When the device detects a high to
low transition on the AD0/CS pin after power-up, SPI mode will be selected. All signals are inputs
and data is clocked in on the rising edge of CCLK.
4.0.3a
SPI Write
To write to the device, follow the procedure below while adhering to the control port
Switching Specifications in section 7.
1) Bring CS low.
2) The address byte on the CDIN pin must then be 00100000.
3) Write to the memory address pointer, MAP. This byte points to the register to be written.
4) Write the desired data to the register pointed to by the MAP.
5) If the INCR bit (see section 4.0.1) is set to 1, repeat the previous step until all the desired
registers are written, then bring CS high.
6) If the INCR bit is set to 0 and further SPI writes to other registers are desired, it is nec-
essary to bring CS high, and follow the procedure detailed from step 1. If no further writes
to other registers are desired, bring CS high.
4.1
Memory Address Pointer (MAP)
MAP
MSB
LS B
DATA
byte 1
byte n
R/W
MA P = Me mo ry A d dre s s P o in te r
ADDRESS
CH IP
CD IN
CC L K
CS
00 10 00 0
Figure 9. Control Port Timing, SPI mode
4.1.1 INCR (AUTO MAP INCREMENT ENABLE)
Default = ‘0’
0 - Disabled,
the MAP will stay constant for successive writes
1 - Enabled,
the MAP will auto increment after each byte is written, allowing block reads or
writes of successive registers
4.1.2 MAP3-0 (MEMORY ADDRESS POINTER)
Default = ‘0000’
76543210
INCR
Reserved
MAP3
MAP2
MAP1
MAP0
00000000
相關PDF資料 |
PDF描述 |
|---|---|
| 0210490185 | CABLE JUMPER 1.25MM .254M 12POS |
| RPP20-1215D/N | CONV DC/DC 20W 9-18VIN +/-15VOUT |
| SDR0604-220YL | INDUCTOR POWER 22UH 1.10A SMD |
| EBA22DTKD-S288 | CONN EDGECARD 44POS .125 EXTEND |
| 380LX562M035H022 | CAP ALUM 5600UF 35V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB4396 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:24-Bit, 192 kHz D/A Converter for Digital Audio |
| CDB4397 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:24-Bit, Multi-Standard D/A Converter for Digital Audio |
| CDB4398 | 功能描述:音頻 IC 開發工具 Eval Bd RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB43L21 | 功能描述:音頻 IC 開發工具 Eval Bd 98dB 96kHz Low-Pwr DAC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| CDB43L22 | 功能描述:音頻 IC 開發工具 Eval Bd LP DAC w/ClassD Spkr Driver RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。