參數資料
型號： CDB8420
廠商： Cirrus Logic Inc
文件頁數： 44/94頁
文件大?。?/td> 0K
描述： EVALUATION BOARD FOR CS8420
標準包裝： 1
主要目的： 音頻，采樣率轉換器
嵌入式： 是，MCU，8 位
已用 IC / 零件： CS8420
主要屬性： 帶數字音頻發射器和接收器的采樣率轉換器
次要屬性： 44.1、48、96 kHz 輸出采樣率，AES/EBU，S/PDIF，EIAJ-340，GUI
已供物品： 板
相關產品： 598-1125-5-ND - IC SAMPLE RATE CONVERTER 28SOIC
其它名稱： 598-1782
DS245F4
49
CS8420
11.3
SRC Invalid State
Occasionally the CS8420 SRC will enter an invalid state. This can happen after the RUN bit has been set
when an AES3 stream is first plugged into the part or when a source device interrupts the SRC input stream.
When this happens, two symptoms may be noticeable: notches occurring in the frequency response and
spurious tones being generated in response to some input frequencies.
To avoid this problem in Software mode, use the microcontroller to monitor the UNLOCK bit in control reg-
ister 10h. When the part achieves lock, clear the RUN bit in register 4 and then set it again. This will reset
all internal state machines. Alternately, the user may use the following sequence:
1.
Power on CS8420.
2.
Write the following register sequence:
3.
Wait for PLL to lock.
4.
Wait 250ms for SRC to lock.
5.
Write the following register sequence:
6.
If PLL goes out of lock, start at step 2 and repeat.
When synchronizing multiple CS8420s, wait for all PLLs to lock before continuing to the next step. These
actions clear the invalid state if it has occurred.
In Hardware mode, monitor the RERR pin for receiver lock status. When the part achieves lock, set the RST
pin low for at least 200
μs and then set it high again. This action clears the invalid state if it has occurred.
When polling the RERR pin again, the user must account for the fact that the RERR pin will be high during
reset and remain high until the PLL has reachieved lock.
In either Software or Hardware mode, when clearing the invalid state, it is advisable to mute any devices
connected to the output of the CS8420.
11.4
C/U Buffer Data Corruption
Occasionally the C/U buffer data may be corrupted. This can happen after the RUN bit has been set and
data has been written to the C/U buffer (20h-37h). If no further data is written to the C buffer after the initial
write and the receiver input is interrupted multiple times, the contents of the buffer may be reset to all zeros.
The buffer will not be corrupted if the buffer data is being updated, only when the data is static and the re-
ceiver input has been interrupted multiple times.
To avoid this problem in Software mode when the C/U buffer contents should remain static, use the micro-
controller to monitor the UNLOCK bit in control register 10h or the RERR pin. If the part indicates the PLL
has lost lock, rewrite the C/U buffer data. Repeat this action every time the PLL goes out of lock.
In Hardware mode, this limitation does not exist as the serial C/U data is being fed directly to the transmitter.
Register
Value
04h
09h
03h
95h
04h
49h
Register
Value
03h
81h
04h
41h
相關PDF資料
PDF描述
VI-J11-EX CONVERTER MOD DC/DC 12V 75W
GEM28DTAT CONN EDGECARD 56POS R/A .156 SLD
6278895-7 C/A 62.5/125 RIS SC MTRJ 7M1
A3BBB-2436G IDC CABLE- ASR24B/AE24G/ASR24B
GSM12DTAN CONN EDGECARD 24POS R/A .156 SLD
相關代理商/技術參數
參數描述
CDB8421 功能描述:音頻 IC 開發工具 2-Ch 32-Bit 192kHz sample rate converte RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB8422 功能描述:界面開發工具 Eval Bd 192kHz SRC S/PDIF Receiver RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
CDB8427 功能描述:音頻 IC 開發工具 Eval Bd 96kHz Dig. Audio Transcvr RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB8952 制造商:Cirrus Logic 功能描述:NOT RECOMMENDED FOR NEW DESIGNS - USE CDB8952T - Bulk 制造商:Cirrus Logic 功能描述:Tools Development kit Kit Con
CDB8952T 功能描述:以太網開發工具 Eval Bd 100BASE-TX/ 10BASE-T Transceiver RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*