- 您現在的位置：買賣IC網 > PDF目錄3791 > COP8CBR9HLQ8 (National Semiconductor)IC MCU CMOS 8BIT 44LLP PDF資料下載
參數資料
| 型號： | COP8CBR9HLQ8 |
| 廠商： | National Semiconductor |
| 文件頁數： | 85/111頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU CMOS 8BIT 44LLP |
| 標準包裝： | 1 |
| 系列： | COP8™ 8C |
| 核心處理器： | COP8 |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 連通性： | Microwire/Plus（SPI），UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 37 |
| 程序存儲器容量： | 32KB（32K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 數據轉換器： | A/D 16x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-WFQFN 裸露焊盤 |
| 包裝： | 剪切帶 (CT) |
| 其它名稱： | *COP8CBR9HLQ8 COP8CBR9HLQ8CT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
Upon Reset, all pending bits, individual enable bits, and the GIE bit are reset to zero. Thus, a maskable
interrupt condition cannot trigger an interrupt until the program enables it by setting both the GIE bit and
the individual enable bit. When enabling an interrupt, the user should consider whether or not a previously
activated (set) pending bit should be acknowledged. If, at the time an interrupt is enabled, any previous
occurrences of the interrupt should be ignored, the associated pending bit must be reset to zero prior to
enabling the interrupt. Otherwise, the interrupt may be simply enabled; if the pending bit is already set, it
will immediately trigger an interrupt. A maskable interrupt is active if its associated enable and pending
bits are set.
An interrupt is an asychronous event which may occur before, during, or after an instruction cycle. Any
interrupt which occurs during the execution of an instruction is not acknowledged until the start of the next
normally executed instruction. If the next normally executed instruction is to be skipped, the skip is
performed before the pending interrupt is acknowledged.
At the start of interrupt acknowledgment, the following actions occur:
1. The GIE bit is automatically reset to zero, preventing any subsequent maskable interrupt from
interrupting the current service routine. This feature prevents one maskable interrupt from interrupting
another one being serviced.
2. The address of the instruction about to be executed is pushed onto the stack.
3. The program counter (PC) is loaded with 00FF Hex, causing a jump to that program memory location.
The device requires seven instruction cycles to perform the actions listed above.
If the user wishes to allow nested interrupts, the interrupts service routine may set the GIE bit to 1 by
writing to the PSW register, and thus allow other maskable interrupts to interrupt the current service
routine. If nested interrupts are allowed, caution must be exercised. The user must write the program in
such a way as to prevent stack overflow, loss of saved context information, and other unwanted
conditions.
The interrupt service routine stored at location 00FF Hex should use the VIS instruction to determine the
cause of the interrupt, and jump to the interrupt handling routine corresponding to the highest priority
enabled and active interrupt. Alternately, the user may choose to poll all interrupt pending and enable bits
to determine the source(s) of the interrupt. If more than one interrupt is active, the user's program must
decide which interrupt to service.
Within a specific interrupt service routine, the associated pending bit should be cleared. This is typically
done as early as possible in the service routine in order to avoid missing the next occurrence of the same
type of interrupt event. Thus, if the same event occurs a second time, even while the first occurrence is
still being serviced, the second occurrence will be serviced immediately upon return from the current
interrupt routine.
An interrupt service routine typically ends with an RETI instruction. This instruction set the GIE bit back to
1, pops the address stored on the stack, and restores that address to the program counter. Program
execution then proceeds with the next instruction that would have been executed had there been no
interrupt. If there are any valid interrupts pending, the highest-priority interrupt is serviced immediately
upon return from the previous interrupt.
NOTE
While executing from the Boot ROM for ISP or virtual E2 operations, the hardware will
disable interrupts from occurring. The hardware will leave the GIE bit in its current state, and
if set, the hardware interrupts will occur when execution is returned to Flash Memory.
Subsequent interrupts, during ISP operation, from the same interrupt source will be lost.
Copyright 2000–2013, Texas Instruments Incorporated
Functional Description
75
相關PDF資料 |
PDF描述 |
|---|---|
| MC9S08SH32VTJ | MCU 8BIT 32K FLASH 20-TSSOP |
| MC9S08SH32VTG | MCU 8BIT 32K FLASH 16-TSSOP |
| MC9S08SH16VWL | MCU 8BIT 16K FLASH 28-SOIC |
| MC9S08SH16VTL | MCU 8BIT 16K FLASH 28-TSSOP |
| MC9S08SH16VTG | MCU 8BIT 16K FLASH 16-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8CBR9HVA8 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8CBR9HVA8/NOPB | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8CBR9IMT8 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8CBR9IMT8/NOPB | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8CBR9KMT8 | 功能描述:IC MCU EEPROM 8BIT 32K 56-TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8C 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
發布緊急采購，3分鐘左右您將得到回復。