1/tC
參數資料
型號: COP8CBR9HLQ8
廠商: National Semiconductor
文件頁數: 94/111頁
文件大?。?/td> 0K
描述: IC MCU CMOS 8BIT 44LLP
標準包裝: 1
系列: COP8™ 8C
核心處理器: COP8
芯體尺寸: 8-位
速度: 20MHz
連通性: Microwire/Plus(SPI),UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 37
程序存儲器容量: 32KB(32K x 8)
程序存儲器類型: 閃存
RAM 容量: 1K x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
數據轉換器: A/D 16x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 44-WFQFN 裸露焊盤
包裝: 剪切帶 (CT)
其它名稱: *COP8CBR9HLQ8
COP8CBR9HLQ8CT
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
1/tC < 10 Hz—Ensured clock rejection.
Table 5-28. WATCHDOG Service Actions
Key
Window
Clock
Action
Data
Monitor
Match
Valid Service: Restart Service Window
Don't Care
Mismatch
Don't Care
Error: Generate WATCHDOG Output
Mismatch
Don't Care
Error: Generate WATCHDOG Output
Don't Care
Mismatch
Error: Generate WATCHDOG Output
5.16.3 WATCHDOG AND CLOCK MONITOR SUMMARY
The following salient points regarding the WATCHDOG and CLOCK MONITOR should be noted:
Both the WATCHDOG and CLOCK MONITOR detector circuits are inhibited during RESET.
Following RESET, the WATCHDOG and CLOCK MONITOR are both enabled, with the WATCHDOG
having the maximum service window selected.
The WATCHDOG service window and CLOCK MONITOR enable/disable option can only be changed
once, during the initial WATCHDOG service following RESET.
The initial WATCHDOG service must match the key data value in the WATCHDOG Service register
WDSVR in order to avoid a WATCHDOG error.
Subsequent WATCHDOG services must match all three data fields in WDSVR in order to avoid
WATCHDOG errors.
The correct key data value cannot be read from the WATCHDOG Service register WDSVR. Any
attempt to read this key data value of 01100 from WDSVR will read as key data value of all 0's.
The WATCHDOG detector circuit is inhibited during both the HALT and IDLE modes.
The CLOCK MONITOR detector circuit is active during both the HALT and IDLE modes. Consequently,
the device inadvertently entering the HALT mode will be detected as a CLOCK MONITOR error
(provided that the CLOCK MONITOR enable option has been selected by the program). Likewise, a
device with WATCHDOG enabled in the Option but with the WATCHDOG output not connected to
RESET, will draw excessive HALT current if placed in the HALT mode. The clock Monitor will pull the
WATCHDOG output low and sink current through the on-chip pull-up resistor.
The WATCHDOG service window will be set to its selected value from WDSVR following HALT.
Consequently, the WATCHDOG should not be serviced for at least 2048 Idle Timer clocks following
HALT, but must be serviced within the selected window to avoid a WATCHDOG error.
The IDLE timer T0 is not initialized with external RESET.
The user can sync in to the IDLE counter cycle with an IDLE counter (T0) interrupt or by monitoring the
T0PND flag. The T0PND flag is set whenever the selected bit of the IDLE counter toggles (every 4, 8,
16, 32 or 64k Idle Timer clocks). The user is responsible for resetting the T0PND flag.
A hardware WATCHDOG service occurs just as the device exits the IDLE mode. Consequently, the
WATCHDOG should not be serviced for at least 2048 Idle Timer clocks following IDLE, but must be
serviced within the selected window to avoid a WATCHDOG error.
Following RESET, the initial WATCHDOG service (where the service window and the CLOCK
MONITOR enable/disable must be selected) may be programmed anywhere within the maximum
service window (65,536 instruction cycles) initialized by RESET. Note that this initial WATCHDOG
service may be programmed within the initial 2048 instruction cycles without causing a WATCHDOG
error.
When using any of the ISP functions in Boot ROM, the ISP routines will service the WATCHDOG
within the selected upper window. Upon return to flash memory, the WATCHDOG is serviced, the
lower window is enabled, and the user can service the WATCHDOG anytime following exit from Boot
ROM, but must service it within the selected upper window to avoid a WATCHDOG error.
Copyright 2000–2013, Texas Instruments Incorporated
Functional Description
83
Product Folder Links: COP8CBR9 COP8CCR9 COP8CDR9
相關PDF資料
PDF描述
MC9S08SH32VTJ MCU 8BIT 32K FLASH 20-TSSOP
MC9S08SH32VTG MCU 8BIT 32K FLASH 16-TSSOP
MC9S08SH16VWL MCU 8BIT 16K FLASH 28-SOIC
MC9S08SH16VTL MCU 8BIT 16K FLASH 28-TSSOP
MC9S08SH16VTG MCU 8BIT 16K FLASH 16-TSSOP
相關代理商/技術參數
參數描述
COP8CBR9HVA8 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CBR9HVA8/NOPB 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CBR9IMT8 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CBR9IMT8/NOPB 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CBR9KMT8 功能描述:IC MCU EEPROM 8BIT 32K 56-TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:COP8™ 8C 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C,IrDA,LIN,SPI,UART/USART 外圍設備:DMA,PDR,POR,PVD,PWM,溫度傳感器,WDT 輸入/輸出數:26 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN,36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND