- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16HCT5VJE8Y Microcontroller PDF資料下載
參數資料
| 型號： | CR16HCT5VJE8Y |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 16/157頁 |
| 文件大?。?/td> | 1256K |
| 代理商： | CR16HCT5VJE8Y |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
www.national.com
16
I bit
The Global Maskable Interrupt Enable (I) bit is
used to enable or disable maskable interrupts.
If this bit and the Local Maskable Interrupt En-
able (E) bit are both set to 1, all maskable inter-
rupts are accepted. Otherwise, only the non-
maskable interrupt is accepted. This bit is auto-
matically cleared to 0 when an interrupt occurs
and automatically set to 1 upon completion of
an interrupt service routine.
Upon reset, all non-reserved bits of the register are cleared
to 0 except for the E bit (bit 9), which is set to 1. When a de-
vice reset occurs, the PSR contents prior to the reset are
stored into register R1, allowing the initialization software to
determine the state of the device prior to the reset operation.
7.4
The Configuration (CFG) register is a 16-bit core register that
determines the size of the INTBASE register. For the device,
the CFG register should always be left in its default state
(cleared to zero), resulting in a 16-bit INTBASE register.
CONFIGURATION REGISTER
7.5
Each instruction operates on one or more operands. An op-
erand can be a register or a memory location.
Most instructions use one, two, or three device registers as
operands. The instruction opcode specifies the registers to
be operated on. Some instructions may use an immediate
value (a value provided in the instruction itself) instead of a
register.
Memory locations are accessed only by the Load and Store
commands. The memory location to use for a particular in-
struction can be specified as an absolute, relative, or far-rel-
ative address.
The instruction set supports the following addressing modes:
Register Mode
The operand is a general-purpose regis-
ter: R0 through R13, RA, or SP. For exam-
ple:
ADDB R1, R2
Immediate
Mode
in the instruction. In a branch instruction,
the immediate operand is a displacement
from the program counter (PC). In the as-
sembly language syntax, a dollar sign indi-
cates an immediate value. For example:
MULW $4, R4
Relative Mode
The operand is located in memory. Its ad-
dress is obtained by adding the contents of
a general purpose register to the constant
value encoded into the displacement field
of the instruction. For example:
LOADW 12(R5), R6
Far-Relative
Mode
dress is obtained by concatenating a pair
of adjacent general-purpose registers to
form a 21-bit value, and adding this value
to the constant value encoded into the dis-
placement field of the instruction.
ADDRESSING MODES
For additional information on the instruction set and instruc-
tion encoding, see the CompactRISC CR16B Programmer's
Reference manual.
7.6
A stack is a one-dimensional data buffer in which values are
entered and removed one at a time. The last valued entered
is the first one removed. A register called the stack pointer
contains the current address of the last item entered on the
stack. In the device, when an item is entered or “pushed”
onto the stack, the stack expands downward in memory (the
stack pointer is decremented). When an item is removed or
“popped” from the stack, the stack shrinks upward in memory
(the stack pointer is incremented).
The device uses two type of stacks: the program stack and
the interrupt stack.
The program stack is used by the software to save and re-
store register values upon entry into and exit from a subrou-
tine. The software can also use the program stack to store
local and temporary variables. The stack pointer for this stack
is the SP register.
The interrupt stack is used to save and restore the program
state when an exception occurs (an interrupt or software
trap). The on-chip hardware automatically pushes the pro-
gram state information onto the stack before the exception
service procedure is executed. Upon exit from the exception
service procedure, the hardware pops this information from
the stack and restores the program state. The stack pointer
for this stack is the ISP register.
STACKS
7.7
Table 7 is a summary list of all instructions in the device in-
struction set. For each instruction, the table shows the mne-
monic and a brief description of the operation performed.
In the Mnemonic column, the lower-case letter “i” is used to
indicate the type of integer that the instruction operates on,
either “B” for byte or “W” for word. For example, the notation
ADDi for the “add” instruction means that there are two forms
of this instruction, ADDB and ADDW, which operate on bytes
and words, respectively.
Similarly, the lower-case string “cond” is used to indicate the
type of condition tested by the instruction. For example, the
notation Jcond represents a class of conditional jump instruc-
tions: JEQ for Jump on Equal, JNE for Jump on Not Equal,
and so on.
INSTRUCTION SET
A constant operand value is specified with-
The operand is located in memory. Its ad-
Absolute Mode
The operand is located in memory. Its ad-
dress is specified within the instruction.
For example:
LOADB 4000, R6
相關PDF資料 |
PDF描述 |
|---|---|
| CR16HCT5VJE9Y | Microcontroller |
| CR16HCT9 | |
| CR16HCT9VJE7 | Microcontroller |
| CR16HCT9VJE7Y | Microcontroller |
| CR16HCT9VJE8 | Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16HCT5VJE9Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT5VJEXY | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9VJE7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE7Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。