n = port number (1 to 12 for DS32512, 1 to 8 for DS32508, 1 to 6 for DS32506). I = " />
參數資料
型號： DS32512N+
廠商： Maxim Integrated Products
文件頁數： 40/130頁
文件大?。?/td> 0K
描述： IC LIU DS3/E3/STS-1 12P 484-BGA
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 30
類型： 線路接口裝置（LIU）
規程： DS3
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 484-BGA
供應商設備封裝： 484-BGA（23x23）
包裝： 管件
DS32506/DS32508/DS32512
17 of 130
7.2 Detailed Pin Descriptions
n = port number (1 to 12 for DS32512, 1 to 8 for DS32508, 1 to 6 for DS32506). I = input, Ipu = input with internal pullup resistor, Ipd = input with
internal pulldown resistor, Ia = analog input, I/O = bidirectional in/out, I/Opd = bidirectional in/out with internal pulldown resistor, O = output, Oz =
high-impedance output (needs an external pullup or pulldown resistor to keep the node from floating), Oa = analog output (high impedance), P=
power supply or ground. All unused input pins without pullup should be tied low. Note: All internal pullup resistors are 50k
Ω tied to 2.2V DC.
Table 7-2. Analog Line Interface Pin Descriptions
NAME
TYPE
FUNCTION
TXPn,
TXNn
Oa
Transmitter Analog Outputs. These differential AMI outputs are coupled to the outbound 75
Ω
coaxial cable through a 1:1 transformer (Figure 4-1). These outputs can be disabled (high
impedance) using the TOEn pin or the TOE or TPD configuration bits. See Section 8.2.8.
RXPn,
RXNn
Ia
Receiver Analog Inputs. These differential AMI inputs are coupled to the inbound 75
Ω coaxial
cable through a 1:1 transformer (Figure 4-1). See Section 8.3.1.
Table 7-3. Digital Framer Interface Pin Descriptions
NAME
TYPE
FUNCTION
TCLKn
I
Transmit Clock. A DS3 (44.736MHz
±20ppm), E3 (34.368MHz ±20ppm), or STS-1
(51.840MHz
±20ppm) clock should be applied at this pin. Data to be transmitted is clocked into
the device at TPOS/TDAT and TNEG either on the rising edge of TCLK (TCLKI = 0) or the
falling edge of TCLK (TCLKI = 1). When pin TCC = 1, all ports are clocked by TCLK1, and
TCLKx (x
≠ 1) are ignored. See Section 8.2.1 for additional details.
TPOSn/
TDATn
I
Transmit Positive AMI/Transmit NRZ Data. This pin is sampled either on the rising edge of
TCLK (TCLKI = 0) or on the falling edge of TCLK (TCLKI = 1). See Section 8.2.2.
TPOSn: When the transmitter is configured to have a bipolar interface (TBIN = 0), a positive
pulse is transmitted on the line when TPOS is high.
TDATn: When the transmitter is configured to have a binary interface (TBIN = 1), the data on
TDAT is transmitted after B3ZS or HDB3 encoding.
TNEGn
I
Transmit Negative AMI. When the transmitter is configured to have a bipolar interface (TBIN =
0), a negative pulse is transmitted on the line when TNEG is high. When the transmitter is
configured to have a binary interface (TBIN = 1), TNEG is ignored and should be wired either
high or low. TNEG is sampled either on the rising edge of TCLK (TCLKI = 0) or the falling edge
of TCLK (TCLKI = 1). See Section 8.2.2.
RCLKn
Oz
Receive Clock. The clock recovered from the receive signal is output on the RCLK pin.
Recovered data is output on the RPOS/RDAT and RNEG/RLCV pins on the falling edge of
RCLK (RCLKI = 0) or the rising edge of RCLK (RCLKI = 1). During a loss-of-signal condition
(RLOSn = 0), the RCLK output signal is derived from the LIU’s reference clock. See Section
RPOSn/
RDATn
Oz
Receive Positive AMI/Receive NRZ Data. This pin is updated either on the falling edge of
RCLK (RCLKI = 0) or the rising edge of RCLK (RCLKI = 1). See Section 8.3.6.
RPOSn: When the receiver is configured to have a bipolar interface (RBIN = 0), RPOS pulses
high for each positive AMI pulse received.
RDATn: When the receiver is configured to have a binary interface (RBIN = 1), RDAT outputs
decoded binary data.
RNEGn/
RLCVn
Oz
Receive Negative AMI/Receive Line-Code Violation. This pin is updated either on the falling
edge of RCLK (RCLKI = 0) or the rising edge of RCLK (RCLKI = 1). See Section 8.3.6 for
further details on code violations.
RNEGn: When the receiver is configured to have a bipolar interface (RBIN = 0), RNEG pulses
high for each negative AMI pulse received.
RLCVn: When the receiver is configured to have a binary interface (RBIN = 1), RLCV pulses
high to flag code violations.
相關PDF資料
PDF描述
DS3254N+ IC LIU DS3/E3/STS-1 144-CSBGA
DS33M33N+ IC MAPPER ETHERNET 256CSBGA
DS33R11+CJ2 IC ETH TXRX T1/E1/J1 256-BGA
DS33R41+ IC TXRX ETHERNET MAP 400-BGA
DS33W11DK+ IC MAPPING ETHERNET 256-CSBGA
相關代理商/技術參數
參數描述
DS32512N# 功能描述:網絡控制器與處理器 IC 12-Port DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS32512N+ 功能描述:網絡控制器與處理器 IC 12-Port DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS32512NA2 制造商:Maxim Integrated Products 功能描述:DS32512 X12 DS3/E3 LIU REVA2 IND - Rail/Tube
DS32512NW 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS32512W 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*