If the temperature of the package case (T" />
參數資料
型號: DSP56301PW80
廠商: Freescale Semiconductor
文件頁數: 7/124頁
文件大?。?/td> 0K
描述: IC DSP 24BIT 80MHZ 208-LQFP
標準包裝: 36
系列: DSP563xx
類型: 定點
接口: 主機接口,SSI,SCI
時鐘速率: 80MHz
非易失內存: ROM(9 kB)
芯片上RAM: 24kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 3.30V
工作溫度: -40°C ~ 100°C
安裝類型: 表面貼裝
封裝/外殼: 208-LQFP
供應商設備封裝: 208-LQFP
包裝: 托盤
DSP56301 Technical Data, Rev. 10
4-2
Freescale Semiconductor
Design Considerations
If the temperature of the package case (TT) is determined by a thermocouple, thermal resistance is
computed from the value obtained by the equation (TJ – TT)/PD.
As noted earlier, the junction-to-case thermal resistances quoted in this data sheet are determined using the first
definition. From a practical standpoint, that value is also suitable to determine the junction temperature from a case
thermocouple reading in forced convection environments. In natural convection, the use of the junction-to-case
thermal resistance to estimate junction temperature from a thermocouple reading on the case of the package will
yield an estimate of a junction temperature slightly higher than actual temperature. Hence, the new thermal metric,
thermal characterization parameter or
Ψ
JT, has been defined to be (TJ – TT)/PD. This value gives a better estimate
of the junction temperature in natural convection when the surface temperature of the package is used. Remember
that surface temperature readings of packages are subject to significant errors caused by inadequate attachment of
the sensor to the surface and to errors caused by heat loss to the sensor. The recommended technique is to attach a
40-gauge thermocouple wire and bead to the top center of the package with thermally conductive epoxy.
4.2 Electrical Design Considerations
Use the following list of recommendations to ensure correct DSP operation.
Provide a low-impedance path from the board power supply to each VCC pin on the DSP and from the
board ground to each GND pin.
Use at least six 0.01–0.1
μF bypass capacitors positioned as close as possible to the four sides of the
package to connect the VCC power source to GND.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VCC and GND pins
are less than 0.5 inch per capacitor lead.
Use at least a four-layer PCB with two inner layers for VCC and GND.
Because the DSP output signals have fast rise and fall times, PCB trace lengths should be minimal. This
recommendation particularly applies to the address and data buses as well as the IRQA, IRQB, IRQC, IRQD,
TA
, and BG pins. Maximum PCB trace lengths on the order of 6 inches are recommended.
Consider all device loads as well as parasitic capacitance due to PCB traces when you calculate
capacitance. This is especially critical in systems with higher capacitive loads that could create higher
transient currents in the VCC and GND circuits.
All inputs must be terminated (that is, not allowed to float) by CMOS levels except for the three pins with
internal pull-up resistors (TRST, TMS, DE).
Take special care to minimize noise levels on the VCCP, GNDP, and GNDP1 pins.
The following pins must be asserted after power-up: RESET and TRST.
CAUTION
This device contains protective circuitry to
guard against damage due to high static
voltage or electrical fields. However, normal
precautions are advised to avoid application
of any voltages higher than maximum rated
voltages
to
this
high-impedance
circuit.
Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage
level (for example, either GND or VCC).
相關PDF資料
PDF描述
VE-26Z-CW-S CONVERTER MOD DC/DC 2V 40W
MIC281-0BM6 TR IC SUPERVISOR THERMAL SOT23-6
VJ1206A821JBBAT4X CAP CER 820PF 100V 5% NP0 1206
VI-21D-CW-F4 CONVERTER MOD DC/DC 85V 100W
EBC05DRES-S13 CONN EDGECARD 10POS .100 EXTEND
相關代理商/技術參數
參數描述
DSP56301UMAD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP56301 Users Manual Addendum
DSP56301VF100 功能描述:數字信號處理器和控制器 - DSP, DSC 100Mhz/100MMACS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56301VF80 功能描述:數字信號處理器和控制器 - DSP, DSC MAP DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56301VF80B1 功能描述:數字信號處理器和控制器 - DSP, DSC DSP56301VF80B1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56301VL100 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:24-Bit Digital Signal Processor