參數資料
型號： EPCS64SI16N
廠商： Altera
文件頁數： 21/40頁
文件大?。?/td> 0K
描述： IC CONFIG DEVICE 64MBIT 16-SOIC
產品培訓模塊： Three Reasons to Use FPGA's in Industrial Designs
標準包裝： 49
系列： EPCS
可編程類型： 系統內可編程
存儲容量： 64Mb
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
封裝/外殼： 16-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 16-SOIC
包裝： 管件
產品目錄頁面： 604 (CN2011-ZH PDF)
其它名稱： 544-1380-5
EPCS64SI16
EPCS64SI16N-ND
Page 28
Power and Operation
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Power and Operation
This section describes the power modes, power-on reset (POR) delay, error detection,
and initial programming state of the EPCS devices.
Power Mode
EPCS devices support active and standby power modes. When the nCS signal is low,
the device is enabled and is in active power mode. The FPGA is configured while the
EPCS device is in active power mode. When the nCS signal is high, the device is
disabled but remains in active power mode until all internal cycles are completed,
such as write or erase operations. The EPCS device then goes into standby power
mode. The ICC1 and ICC0 parameters list the VCC supply current when the device is in
active and standby power modes. For more information, refer to Table 21 on page 34.
Power-On Reset
During the initial power-up, a POR delay occurs to ensure the system voltage levels
have stabilized. During the AS configuration, the FPGA controls the configuration
and has a longer POR delay than the EPCS device.
f For more information about the POR delay time, refer to the configuration chapter in
the appropriate device handbook.
Error Detection
During the AS configuration with the EPCS device, the FPGA monitors the
configuration status through the nSTATUS and CONF_DONE pins. If an error condition
occurs, if the nSTATUS pin drives low or if the CONF_DONE pin does not go high, the
FPGA begins reconfiguration by pulsing the nSTATUS and nCSO signals, which controls
the chip select (nCS) pin on the EPCS device.
After an error, the configuration automatically restarts if the Auto-Restart Upon
Frame Error
option is turned on in the Quartus II software. If the option is turned off,
the system must monitor the nSTATUS signal for errors and then pulse the nCONFIG
signal low to restart configuration.
相關PDF資料
PDF描述
XC17S15ASO20C IC PROM SER 5000 C-TEMP 20-SOIC
ICL7663SACBAZA-T IC REG LDO ADJ 40MA 8-SOIC
HMC25DRYN-S734 CONN EDGECARD 50POS DIP .100 SLD
EEC26DRYH-S13 CONN EDGECARD 52POS .100 EXTEND
XC17S15APD8I IC PROM SER 5000 I-TEMP 8-DIP
相關代理商/技術參數
參數描述
EPCSC2.5T 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
EPCSC2.5T1-2 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
EPCSC2.5T2-2 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
EPCSC2.5T2-2/BL 功能描述:接線端子工具和配件 End Plate , Black (50) RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
EPCSC2.5T2-2/BU 功能描述:接線端子工具和配件 End Plate , Blue (50) RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*