- 您現在的位置：買賣IC網 > PDF目錄16441 > EVAL-AD9880-ABZ (Analog Devices Inc)KIT MODULE VIDEO INPUT AD9880 PDF資料下載
參數資料
| 型號： | EVAL-AD9880-ABZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 52/64頁 |
| 文件大小： | 0K |
| 描述： | KIT MODULE VIDEO INPUT AD9880 |
| 標準包裝： | 1 |
| 主要目的： | 視頻，視頻處理 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9880 |
| 主要屬性： | HDMI 接收器和模擬接口 |
| 次要屬性： | 3 路 8 位 150MSPS ADC |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
AD9880
Rev. 0 | Page 56 of 64
2-WIRE SERIAL CONTROL PORT
A 2-wire serial interface control interface is provided in the
AD9880. Up to two AD9880 devices can be connected to the
2-wire serial interface, with a unique address for each device.
The 2-wire serial interface comprises a clock (SCL) and a
bidirectional data (SDA) pin. The analog flat panel interface
acts as a slave for receiving and transmitting data over the serial
interface. When the serial interface is not active, the logic levels
on SCL and SDA are pulled high by external pull-up resistors.
Data received or transmitted on the SDA line must be stable for
the duration of the positive-going SCL pulse. Data on SDA must
change only when SCL is low. If SDA changes state while SCL is
high, the serial interface interprets that action as a start or stop
sequence.
There are six components to serial bus operation:
Start signal
Slave address byte
Base register address byte
Data byte to read or write
Stop signal
Acknowledge (Ack)
When the serial interface is inactive (SCL and SDA are high)
communications are initiated by sending a start signal. The start
signal is a high-to-low transition on SDA while SCL is high.
This signal alerts all slaved devices that a data transfer sequence
is coming.
The first eight bits of data transferred after a start signal
comprise a seven bit slave address (the first seven bits) and a
single R/W\ bit (the eighth bit). The R/W\ bit indicates the
direction of data transfer, read from (1) or write to (0) the slave
device. If the transmitted slave address matches the address of
the device (set by the state of the SA0 input pin as shown in
Table 97), the AD9880 acknowledges by bringing SDA low on
the 9th SCL pulse. If the addresses do not match, the AD9880
does not acknowledge.
Table 97. Serial Port Addresses
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
A6 (MSB)
A5
A4
A3
A2
A1
A0
1
0
1
0
Data Transfer via Serial Interface
For each byte of data read or written, the MSB is the first bit of
the sequence.
If the AD9880 does not acknowledge the master device during a
write sequence, the SDA remains high so the master can gener-
ate a stop signal. If the master device does not acknowledge the
AD9880 during a read sequence, the AD9880 interprets this as
end of data. The SDA remains high, so the master can generate
a stop signal.
Writing data to specific control registers of the AD9880 requires
that the 8-bit address of the control register of interest be writ-
ten after the slave address has been established. This control
register address is the base address for subsequent write opera-
tions. The base address auto-increments by one for each byte of
data written after the data byte intended for the base address. If
more bytes are transferred than there are available addresses,
the address does not increment and remains at its maximum
value. Any base address higher than the maximum value does
not produce an acknowledge signal.
Data are read from the control registers of the AD9880 in a
similar manner. Reading requires two data transfer operations:
The base address must be written with the R/W bit of the slave
address byte low to set up a sequential read operation.
Reading (the R/W bit of the slave address byte high) begins at
the previously established base address. The address of the read
register auto-increments after each byte is transferred.
To terminate a read/write sequence to the AD9880, a stop signal
must be sent. A stop signal comprises a low-to-high transition
of SDA while SCL is high.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first genera-
ting a stop signal to terminate the current communication. This
is used to change the mode of communication (read, write)
between the slave and master without releasing the serial
interface lines.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADV7611EB2Z | BOARD EVALUATION FOR ADV7611 |
| 1-1906012-2 | CA 2.0MM OFNR 50/125,LC SEC RED |
| 4922R-17L | INDUCTOR 22UH POWER SMD |
| GMM12DTAD | CONN EDGECARD 24POS R/A .156 SLD |
| S200-2-W1-22-9 | SOLDERSLEEVE SHLD TERMI W/LEADS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADAS1000EBZU1 | 功能描述:EVAL BOARD ADAS1000 ECG AFE RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| EVAL-ADAS1000SDZ | 功能描述:數據轉換 IC 開發工具 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| EVAL-ADAS1000SDZU3 | 制造商:Analog Devices 功能描述:EVALUATION KIT - Boxed Product (Development Kits) |
| EVAL-ADAS1000SDZU4 | 制造商:Analog Devices 功能描述:EVAL BOARD ANAS1000 ECG AFE |
| EVAL-ADAS1127CBZ | 功能描述:BOARD EVAL FOR ADAS1127 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。