- 您現在的位置：買賣IC網 > PDF目錄375996 > GE28F640W30B70 EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC PDF資料下載
參數資料
| 型號： | GE28F640W30B70 |
| 英文描述： | EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| 中文描述： | 的EEPROM | FLASH動畫| 4MX16 |的CMOS | BGA封裝| 56PIN |塑料 |
| 文件頁數： | 26/91頁 |
| 文件大?。?/td> | 994K |
| 代理商： | GE28F640W30B70 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁
1.8 Volt Intel
Wireless Flash Memory with 3 Volt I/O
26
Datasheet
5.2
Factory Programming
The standard factory programming mode uses the same commands and algorithm as the Word
Program mode (40h/10h). When V
PP
is at V
PP1
, program and erase currents are drawn through
VCC. If VPP is driven by a logic signal, V
PP1
must remain above the V
PP1
Min value to perform in-
system flash modifications. When VPP is connected to a 12 V power supply, the device draws
program and erase current directly from VPP. This eliminates the need for an external switching
transistor to control the V
PP
voltage.
Figure 14, “Examples of VPP Power Supply Configurations”
on page 42
shows examples of flash power supply usage in various configurations.
Figure 5. Word Program Flowchart
Suspend
Program
Loop
Start
Write 40h,
Word Address
Write Data
Word Address
Read Status
Register
SR[7] =
Full Program
Status Check
(if desired)
Program
Complete
FULL PROGRAM STATUS CHECK PROCEDURE
Suspend
Program
Read Status
Register
Program
Successful
SR[3] =
SR[1] =
0
0
SR[4] =
0
1
1
1
1
0
No
Yes
V
PP
Range
Error
Device
Protect Error
Program
Error
WORD PROGRAM PROCEDURE
SR[3] MUST be cleared before the WSM will allow further
program attempts
Only the Clear Staus Register command clears SR[4:3,1].
If an error is detected, clear the status register before
attempting a program retry or other error recovery.
Standby
Standby
OpBus
Check SR[3]
1 = V
PP
error
Check SR[4]
1 = Data program error
Comments
Repeat for subsequent programming operations.
Full status register check can be done after each program or
after a sequence of program operations.
Comments
OpBus
Data = 40h
Addr = Location to program (WA)
Write
Program
Setup
Data = Data to program (WD)
Addr = Location to program (WA)
Write
Data
Read SRD
Toggle CE# or OE# to update SRD
Read
Check SR[7]
1 = WSM ready
0 = WSM busy
Standby
Standby
Check SR[1]
1 = Attempted program to locked block
Program aborted
相關PDF資料 |
PDF描述 |
|---|---|
| GE28F640W30B85 | EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GE28F640W30T70 | EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GE28F640W30T85 | EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GF4435 | TRANSISTOR | MOSFET | P-CHANNEL | 30V V(BR)DSS | 8A I(D) | SO |
| GF4450 | TRANSISTOR | MOSFET | N-CHANNEL | 60V V(BR)DSS | 7.5A I(D) | SO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GE28F640W30B85 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GE28F640W30T70 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GE28F640W30T85 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GE28F800B3BA90 | 制造商:Intel 功能描述:NOR Flash, 512K x 16, 45 Pin, Plastic, BGA |
| GE28F800B3TA90 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 Volt Advanced Boot Block Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。