參數資料
型號： KSZ8692XPB
廠商： Micrel Inc
文件頁數： 13/42頁
文件大小： 0K
描述： IC ARM9 PHY 10/100MBPS 400-PBGA
標準包裝： 40
系列： KSZx692
應用： 網絡和通信
核心處理器： ARM9
程序存儲器類型： 外部程序存儲器
控制器系列： KSZ
接口： EBI/EMI，以太網，I²C，I²S，PCI，SPI，UART/USART，USB
輸入/輸出數： 20
電源電壓： 1.235 V ~ 1.365 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 400-BGA
包裝： 托盤
供應商設備封裝： 400-PBGA（24x24）
產品目錄頁面： 1080 (CN2011-ZH PDF)
其它名稱： 576-3537
Micrel, Inc.
KSZ8692MPB/KSZ8692XPB
March 2010
20
M9999-031810-4.0
frame’s destination.
If the networkcontroller scans a frame and does not find the specific sequence shown above, it discards the frame and
takes no further action. If the KSZ8692MPB/KSZ8692XPB controller detects the data sequence, however, it then alerts
the device’s power management circuitry to wake up the system.
IPv6 Support
The KSZ8692MPB/KSZ8692XPB provides the following IPv6 support in the hardware:
Generates the checksum for IPv6 TCP/UDP packets based on register configuration (LAN MAC DMA Transmit
Control Register and WAN MAC DMA Transmit Control Register) or Transmit Descriptor 1 (TDES1). The register
setting is static configuration and the TDES1 setting is packet-based configuration.
Filters IPv6 packets with TCP/UDP errors (LAN MAC DMA Receive Control Register and WAN MAC DMA Receive
Control Register).
Supports up to 8 Source IP or Destination IP-based filtering (LAN/WAN Access Control List)
Refer to the Register Description Document for more details.
DMA Controller
Integrated DMA controller connects data port of two Ethernet MACs, two USB 2.0 ports, PCI 2.3 bus interface, and SDIO
interface (for KSZ8692MPB only) via dedicated channels to DDR memory controller for moving large amounts of data
without significant ARM processor intervention. A typical DMA channel usage is to move data from these interfaces into
DDR memory. The data in the memory is processed by the ARM processor and driven back by the DMA channel to the
external interface. Additionally, the ARM processor itself has a dedicated DMA channel to access the DDR memory
controller. Flash/ROM/SRAM, NAND controller, and peripherals do not have dedicated DMA channel and therefore,
depend on the ARM processor for transfer of data to DDR memory. DMA channel interfaces are shown in the functional
block diagram on page 8 and 9.
The arbitration of all requests from DMA channels are handled by the DDR memory controller and pipelined for best
performance. The memory controller supports programmable bandwidth allocation for each DMA channel, thus enabling
the designer to optimize I/O resource utilization of memory.
UART Interface
The KSZ8692MPB/KSZ8692XPB support four independent, high-speed UARTs; UART1, UART2, UART3 and UART4.
The UART ports enhance the system availability for legacy serial communication application and console port display.
UART1, UART2, UART3 and UART4 support maximum baud rate of 5 Mbps including standard rates. The higher rates
allow for Bluetooth and GSM applications.
UART1 supports CTSN, DSRN, DCDN modem control pins in addition to RXD and TXD data pins. For UART2, UART3,
UART4 only CTSN and RTSN control pins in addition to RXD and TXD data pins are supported.
Timers and Watchdog
Two programmable 32-bit timers with one capable of watchdog timer function. These timers can operate in a very flexible
way. The host can control the timeout period as well as the pulse duration. Both timers can be enabled with interrupt
capability. When the watchdog timer is programmed and the timer setting expires, the KSZ8692MPB/KSZ8692XPB resets
itself and also asserts WRSTO to reset other devices in the system.
GPIO
Twenty general purpose I/O (GPIO) are individually programmable as input or output. Some GPIO ports are
programmable for alternate function as listed below:
Four GPIO programmable as inputs for external interrupts
Two GPIO programmable as 32-bit timers output
Six GPIO programmable as CTSN and RTSN control pins for UART2, UART3, UART4
One GPIO programmable as SDIO Line Status LED driver (for KSZ8692MPB only)
One GPIO programmable as ARM CPU interrupt line activity.
See Signal Description list for detailed GPIO map.
相關PDF資料
PDF描述
KSZ8695P IC ARM9 W/MMU PHY 10/100 289PBGA
KSZ8695X IC SWITCH 10/100 5PORT 208PQFP
KSZ8721BI TR TXRX PHY 10/100 2.3.3/5V 48-SSOP
KSZ8721BLI TR TXRX PHY 10/100 2.3.3/5V 48-LQFP
KSZ8721CL A2 TR TXRX PHY 10/100 3.3V 48-LQFP
相關代理商/技術參數
參數描述
KSZ8695P 功能描述:網絡控制器與處理器 IC Multi-Port PCI Gateway Solution(Lead Free) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
KSZ8695PI 功能描述:網絡控制器與處理器 IC Multi-Port PCI Gateway Solution (Lead Free) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
KSZ8695P-MDP-EVAL 功能描述:網絡開發工具 KSZ88695P-MDP Evaluation Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
KSZ8695P-MMB-EVAL 功能描述:網絡開發工具 KSZ8695P-MMB Evaluation Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
KSZ8695PX 功能描述:網絡控制器與處理器 IC Integrated Multi-Port Gateway Solution w/ Single PCI(Lead Free) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*