參數資料
型號: M30240S9-XXXFP
廠商: Mitsubishi Electric Corporation
英文描述: 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
中文描述: 單片16位CMOS微機
文件頁數: 135/142頁
文件大?。?/td> 1637K
代理商: M30240S9-XXXFP
1-135
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Preliminary Specifications REV. E
Specifications in this manual are tentative and subject to change
Frequency Synthesizer Interface and DC-DC Converter
5.1.2 Set up of Frequency Synthesizer and DC-DC Converter
Figure 1.118: PLL, DC-DC Converter and USB Functional Block Diagram
A functional block diagram of the USB system on the M30240 which shows how the control signals
affect operation is given in Figure 1.118
5.1.2.1 Set up after Hardware Reset
A Hardware Reset occurs when either the RESET pin is brought low for more than 2
μ
s or an invalid
opcode is fetched by the CPU. The frequency synthesizer (PLL) and DC-DC converter should be set
up as follows in the Hardware Reset routine (see Figure 1.119),
Power up the M30240 and other components on the peripheral device for less than 100 mA opera-
tion. The current limit only applies for bus powered devices.
Configure the PLL for 48MHz f(VCO) operation.
Enable the PLL by setting FSE (bit 0 of the Frequency Synthesizer Control Register (FSC)) to a “1”,
then wait for 2 ms.
Check the lock status bit (LS, bit 7 of FSC).
If the bit is a “1”, go on.
If the bit is a “0”, wait 0.1 ms longer and then re-check the bit.
Enable the DC-DC converter in high current mode by setting USBC4 (bit 4 of the USB Control Reg-
ister (USBC)) to a “1” and keeping USBC3 (bit 3 of USBC) a “0”. High current mode should always
be used during normal USB operation. Low current mode should only be used during a USB sus-
pend.
Wait (C + 1)ms (where C equals the external capacitance connected to the Ext Cap pin in
μ
F) for
the voltage on Ext Cap to reach a steady state voltage of approximately 3.3V. (Since the D+ pullup
is connected to the Ext Cap pin, the upstream hub will detect that the peripheral device has been
plugged in once the voltage on D+ reaches approximately 2.0 V.)
Example: A 2.2
μ
F
capacitor connected to Ext Cap requires 3.2 ms for the voltage on Ext Cap to be stable.
33
33
D+
D-
USB FCU
2.2
μ
F
0.1
μ
F
Ext Cap
Frequency
Synthesizer
enable
f(Xin)
FSE
LS
1
USB Transceiver
DC-DC Converter
USBC3
USBC4
USBC7
USBC7
USBC5
USBCLK
(48MHz)
lock
enable
enable
(enable)
(enable)
enable
current
mode
相關PDF資料
PDF描述
M30245M4-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F4-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245M8-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F8-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F8-XXXFP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M30240SA 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SA-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SC 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SC-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER