參數資料
型號: M30240S9-XXXFP
廠商: Mitsubishi Electric Corporation
英文描述: 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
中文描述: 單片16位CMOS微機
文件頁數: 52/142頁
文件大?。?/td> 1637K
代理商: M30240S9-XXXFP
1-52
Mitsubishi microcomputers
M30240 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Preliminary Specifications REV. E
Specifications in this manual are tentative and subject to change
Universal Serial Bus
2.18.4.5 USB Interrupt Status Registers 1 and 2
USB Interrupt Status Registers 1 and 2
,
shown in Figure 1.34 and Figure 1.35, are used to indicate the con-
dition that caused a USB function interrupt and USB Reset, Suspend and Resume Interrupts to the CPU. A
“1” indicates the corresponding condition caused an interrupt. The USB Interrupt Status Register bits can be
cleared by writing a “1” to the corresponding bit.
INTST0 is set to a “1” by the USB FCU when (in Endpoint 0 CSR):
A packet of data is successfully received (EP0CSR0 - OUT_PKT_RDY is set by the USB FCU)
A packet of data is successfully sent (EP0CSR - IN_PKT_RDY is cleared by the USB FCU)
EP0CSR3 (DATA_END) bit is cleared by the USB FCU
EP0CSR4 (FORCE_STALL) bit is set by the USB FCU
EP0CSR5 (SETUP_END) bit is set by the USB FCU
INTST2, INTST4, INTST6 or INTST8 is set to a “1” by the USB FCU when (in Endpoint x IN CSR):
A packet of data is successfully sent (INXCSR0 - IN_PKT_RDY is cleared by the USB FCU)
INXCSR1 (UNDER_RUN) bit is set by the USB FCU
INTST3, INTST5, INTST7 or INTST9 is set to a “1” by the USB FCU when (in Endpoint xOUT CSR):
A packet of data is successfully received (OUTXCSR0 - OUT_PKT_RDY is set by the USB FCU)
OUTXCSR1 (OVER_RUN) bit is set by the USB FCU
OUTXCSR4 (FORCE_STALL) bit is set by the USB FCU
INTST12 is set to a “1” by the USB FCU when an overrun or underrun condition occurs in any of the endpoints.
INTST13 is set to a “1” by the USB FCU when a USB reset signaling from the host is received. All internal
register bits except this bit are reset to their default values when the USB reset is received.
INTST14 is set to a “1” by the USB FCU when the USB FCU is in the suspend state and non-idle signaling is
received from D+/D-.
INTST15 is set to a “1” by the USB FCU when D+/D- are in the idle state for more than 3ms.
Figure 1.34: USB Interrupt Status Register 1
USB Interrupt Status Register 1
Symbol
USBIS1
Address
0302
16
When reset
00
16
Bit name
Bit symbol
b7
b6
b5
b4
b3
b2
b1
0
b0
Function
W
R
Reserved
Must always be set to "0"
INTST0
INTST2
INTST3
INTST4
INTST5
INTST6
INTST7
USB Endpoint 0 Interrupt
Status Flag
USB Endpoint 1 IN
Interrupt Status Flag
USB Endpoint 1 OUT
Interrupt Status Flag
USB Endpoint 2 IN
Interrupt Status Flag
USB Endpoint 2 OUT
Interrupt Status Flag
USB Endpoint 3 IN
Interrupt Status Flag
USB Endpoint 3 OUT
Interrupt Status Flag
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
0 : No interrupt request issued
1 : Interrupt request issued
相關PDF資料
PDF描述
M30245M4-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F4-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245M8-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F8-XXXGF SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245F8-XXXFP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M30240SA 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SA-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SC 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30240SC-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M30245 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER