參數資料
型號： M7040N-100ZA1T
廠商： 意法半導體
英文描述： 64K x 72-bit Entry NETWORK PACKET SEARCH ENGINE
中文描述： 64K的× 72位的網絡數據包進入搜索引擎
文件頁數： 20/159頁
文件大?。?/td> 1088K
代理商： M7040N-100ZA1T
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁
M7040N
20/159
Command Bus (CMD[10:0].
[1:0] specifies the
command; [10:2] contains the command parame-
ters. The descriptions of individual commands ex-
plains the details of the parameters. The encoding
of commands based on the [1:0] field are:
–
00: PIO READ
–
01: PIO WRITE
–
10: SEARCH
–
11: LEARN
Command Valid (
CMDV)
.
Qualifies the CMD bus
as follows:
–
0: No Command
–
1: Command
Address/Data Bus (
DQ[71:0])
.
Carries the Read
and WRITE address as well as the data during
register, data, and mask array operations. It car-
ries the compare data during search operations. It
also carries the SRAM address during SRAM PIO
accesses.
READ Acknowledge (ACK).
Indicates that valid
data is available on the DQ Bus during register,
data, and mask array READ operations, or the
data is available on the SRAM data bus during
SRAM READ operations.
Note:
ACK Signals require a weak external pull-
down resistor such as 47 or 100 K
.
End of Transfer (EOT).
Indicates
burst transfer during READ or WRITE burst oper-
ations.
Note:
EOT Signals require a weak external pull-
down resistor such as 47 K
or 100 K
.
SEARCH Successful Flag (SSF).
When assert-
ed, this signal indicates that the device is the glo-
bal winner in a SEARCH operation.
SEARCH Successful Flag Valid (SSV).
When
asserted, this signal qualifies the SSF signal.
Multiple Hit Flag (MULTI_HIT).
When asserted,
this signal indicates that there is more than one lo-
cation having a match on this device.
High Speed (HIGH_SPEED).
When this signal is
high, the device will run up to 100MHz and perform
100 million searches per second. However, in this
mode, a TLSZ value of '00' is not supported in a
system of a single device. Furthermore, the device
will only support a TLSZ of '00' and '01' if more
than one device is cascaded to form database ta-
bles.
the
end
of
Clock Tune [3:0] (CLK_TUNE[3:0]).
These test
pins should be set to logic level 1001.
SRAM Address (SADR[23:0]).
This
tains address lines to access off-chip SRAMs that
contain associative data. See Table 52, page 128
for the details of the generated SRAM address. In
a database of multiple M7040Ns, each corre-
sponding bit of SADR from all cascaded devices
must be connected.
SRAM Chip Enable (CE_L).
This is Chip Enable
control for external SRAMs. In a database of mul-
tiple M7040Ns, CE_L of all cascaded devices
must be connected. This signal is then driven by
only one of the devices.
SRAM Write Enable (WE_L).
This is Write En-
able control for external SRAMs. In a database of
multiple M7040Ns, WE_L of all cascaded devices
must be connected together. This signal is then
driven by only one of the devices.
SRAM Output Enable (OE_L).
This
Enable control for external SRAMs. Only the last
device drives this signal (with the LRAM bit set).
Address Latch Enable (ALE_L).
When this sig-
nal is low, the addresses are valid on the SRAM
Address Bus. In a database of multiple M7040Ns,
the ALE_L of all cascaded devices must be con-
nected. This signal is then driven by only one of
the devices.
Local Hit In (LHI[6:0]).
These
cade the device to form a larger table size. One
signal of this bus is connected to the LHO[1] or
LHO[0] of each of the upstream devices in a block.
Connect all unused LHI pins to a logic '0.' (For
more
information,
see
page 124.)
Local Hit Out (LHO[1:0]).
LHO[1]
are the same logical signal. LHO[1] or LHO[0] is
connected to one input of the LHI bus of up to four
downstream devices (in a block that contains up to
eight
devices).
(For
more
DEPTH-CASCADING, page 124.)
Block Hit In (BHI[2:0]).
Inputs from the previous
BHO[2:0] are tied to the BHI[2:0] of the current de-
vice (see DEPTH-CASCADING, page 124). In a
four-block system, the last block can contain only
seven devices because the ID code 11111 is used
for broadcast access.
Block Hit Out (BHO[2:0]).
These outputs from
the last device in a block are connected to the
BHI[2:0] inputs of the devices in the downstream
blocks (see DEPTH-CASCADING, page 124).
bus
con-
is
Output
pins
depth-cas-
DEPTH-CASCADING,
and
LHO[0]
information,
see
相關PDF資料
PDF描述
M708 PCM REMOTE CONTROL TRANSMITTER
M708A PCM REMOTE CONTROL TRANSMITTER
M708B1 PCM REMOTE CONTROL TRANSMITTER
M708AB1 PCM REMOTE CONTROL TRANSMITTER
M709 PCM REMOTE CONTROLL TRANSMITTERS
相關代理商/技術參數
參數描述
M7041 制造商:Tamura Corporation of America 功能描述:
M7045 制造商:Tamura Corporation of America 功能描述:
M705-5090142 功能描述:直流電源連接器 FEMALE STEREO JACK RoHS:否 制造商:Kycon 產品:Receptacles 觸點內徑: 觸點外徑: 中心腳長度: 電流額定值:7.5 A 電壓額定值:20 V 安裝角:Right 安裝風格:Cable
M705-5090242 功能描述:RCA Phono連接器 FEMALE STEREO JACK RoHS:否 制造商:Neutrik 型式:Male 端接類型:Solder 安裝風格:Cable 方向:Horizontal
M705-510046 功能描述:RCA Phono連接器 DC JACKS RoHS:否 制造商:Neutrik 型式:Male 端接類型:Solder 安裝風格:Cable 方向:Horizontal
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*