參數資料
型號: MC33989
廠商: 飛思卡爾半導體(中國)有限公司
元件分類: CAN
英文描述: System Basis Chip with High Speed CAN Transceiver(帶高速CAN收發器的系統基片)
中文描述: 系統基礎芯片的高速CAN收發器(帶高速的CAN收發器的系統基片)
文件頁數: 10/32頁
文件大?。?/td> 676K
代理商: MC33989
MC33989
10
MC33989
Figure 3. Transient test pulses for CANH and CANL
Figure 4. Transceiver AC characteristics
3.1
CAN error detection and wake up
The error and the wake up are reported in the CANR register.
3.1.1
Dominant State Time-out
This protection is based on the fact that all CAN signals can not have more than five bits in a row with the same state. In case
of a condition the Tx pin is stuck at 0v, the transceiver would hold the bus in dominant state making it impossible to the others
CAN modules to use the bus. The protection acts releasing the bus when a dominant signal with more than 350uS typical (
Tdout
time)
is present in the Tx signal. After entering the fault condition the driver is disabled. To clear this disabled state the CAN
transceiver needs to have its input going to recessive state.
3.1.2
Internal Error output flags
There are internal error flags to signals when one of the below condition happens. The errors are reported in CAN register.
Thermal protection activated (bit THERM)
Over Current detection in CANL or CANH pins (bit CUR).
Time-out condition for dominant state (bit TXF).
3.1.3
Sleep mode & Wake-up via CAN bus feature
The HSCAN interface enters in a low consumption mode when the “CAN sleep mode” is enabled. In this mode the HSCAN
module will have a 60uA consumption via internal 5V.
When in sleep mode the transmitter and the receiver are disabled, the only part of circuit which remains working is the wake
up module which contains a special low power receiver to check the bus lines and according to its activity generate a wake up
output signal. The conditions for the wake is meet when there are 3 valid pulses in a row. A valid signal must have a pulse width
bigger than 0.5us and no more than 0.5ms.
CAN H
CAN L
Transient Pulse
Generator
(note)
Gnd
Gnd
1nF
1nF
note: Waveform in accordance to ISO7637 part1, test pulses 1, 2, 3a and 3b.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC33990 J-1850 SERIAL TRANSCEIVER(J-1850總線收發器)
MC33991 Gauge Driver Integrated Circuit(標尺驅動器集成電路)
MC33993 Multiple Switch Detection Interface(多開關監測接口)
MC33997 Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源)
MC33998 Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源)
相關代理商/技術參數
參數描述
MC33989DW 功能描述:CAN 接口集成電路 SBC HIGH SPEED RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33989DWR2 功能描述:CAN 接口集成電路 SBC HIGH SPEED RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33989PEG 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33989PEGR2 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33990D 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)