- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33989 (飛思卡爾半導體(中國)有限公司) System Basis Chip with High Speed CAN Transceiver(帶高速CAN收發器的系統基片) PDF資料下載
參數資料
| 型號： | MC33989 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | CAN |
| 英文描述： | System Basis Chip with High Speed CAN Transceiver(帶高速CAN收發器的系統基片) |
| 中文描述： | 系統基礎芯片的高速CAN收發器（帶高速的CAN收發器的系統基片） |
| 文件頁數： | 14/32頁 |
| 文件大小： | 676K |
| 代理商： | MC33989 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
14
MC33989
MC33989
Once stop mode is entered the SBC could wake up from the V1 regulator over current detection. In order to allow time for the
MCU to complete the last CPU instruction to allow MCU to enter its low power mode, a deglitcher time of typicall 40us is
implemented.
figure below indicate operation to enter stop mode.
4.8
Reset and watchdogb pins, sofwtare watchdog operations:
4.8.1
Software watchdog (selectable window or time out watchdog)
Software watchdog is used in the SBC normal and stand-by modes for the MCU monitoring. The watchdog can be either
window or time out. This is selectable by SPI (register TIM1, bit WDW). Default is window watchdog. The period for the watchdog
is selectable from SPI from 10 to 350ms (register TIM1, bits WDT0 and WDT1). When the window watchdog is selected, the
closed window is the first part of the selected period, and the open window is the second part of the period. Refer to SPI TIM
register description. The watchdog can only be cleared within the open window time. An attempt to clear the watchdog in the
closed window will generate a reset. Watchdog is cleared through SPI by addressing the TIM1 register.
4.8.2
Reset pin description
A reset output is available in order to reset the microcontroller. Two operation modes for the reset pin are available, mode 1
and mode 2 (refer to table for reset pin operation).
The reset cause when SBC is in mode 1 are:
- Vdd1 falling out of range: if Vdd1 falls below the reset threshold (parameter
Rst-th
), the reset pin is pull low until Vdd1 return
to nominal voltage.
- Power on reset: at device power on or at device wake up from sleep mode, the reset is maintained low until Vdd1 is within its
operation range.
- Watchdog time out: if the watchdog is not cleared the SBC will pull the reset pin low for the duration of the reset duration time
(
parameter: reset-dur).
In mode 2, the reset pin is not activated in case of watchdog time out. Refer to” table for reset pin operation“for mode detail.
For debug purposes at 25°C, reset pin can be shorted to 5V, thanks to its internal limited current drive capability.
4.8.3
Reset and Wdogb operation: mode1 and mode 2 (safe mode):
The watchdog and reset functions have two modes of operation: mode 1 and mode 2 (mode 2 is also called safe mode).
These modes are independent of the SBC modes (Normal, stand-by, sleep, stop). Mode 1 or mode 2 selection is done through
SPI (register MCR, bit SAFE). Default mode after reset is mode 1.
Table below is the reset and watchdog output mode of operation. Two modes (mode 1 and mode 2) are available and are
selectable through the SPI, safe bit. Default operation after reset or power up is mode 1.
In both modes reset is active at device power up and wake up.
In mode 1: Reset is activated in case of Vdd1 fall or watchdog not triggered. Wdogb output is active low as soon as reset goes
low and stays low as long as the watchdog is not properly re-activated by SPI.
In mode 2, safe mode: Reset in not activated in case of Watchdog failure. WDOGB output has same behavior as in mode 1.
The Wdogb output pin is a push pull structure than can drive external component of the application in order for instance to sig-
nal MCU wrong operation.
Events
Mode
WDOGB
output
Reset
output
Device power up
1 or 2 (safe mode)
low to high
low to high
- Vdd1 normal
- Watchdog properly triggered
1
high
high
SPI CSB
SPI Stop / Sleep command
SBC in Normal or Standby mode
SBC in stop mode
no Idd1 over I wake up
SBC in stop mode
with Idd1over I wake up
Idd1 - dglt
Tcsb-stop
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33990 | J-1850 SERIAL TRANSCEIVER(J-1850總線收發器) |
| MC33991 | Gauge Driver Integrated Circuit(標尺驅動器集成電路) |
| MC33993 | Multiple Switch Detection Interface(多開關監測接口) |
| MC33997 | Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源) |
| MC33998 | Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33989DW | 功能描述:CAN 接口集成電路 SBC HIGH SPEED RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33989DWR2 | 功能描述:CAN 接口集成電路 SBC HIGH SPEED RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33989PEG | 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33989PEGR2 | 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33990D | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。