- 您現在的位置：買賣IC網 > PDF目錄45372 > MPC8569CVTANKGA (FREESCALE SEMICONDUCTOR INC) RISC PROCESSOR, PBGA783 PDF資料下載
參數資料
| 型號： | MPC8569CVTANKGA |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | RISC PROCESSOR, PBGA783 |
| 封裝： | 29 X 29 MM, 1 MM PITCH, PLASTIC, BGA-783 |
| 文件頁數： | 67/126頁 |
| 文件大?。?/td> | 2847K |
| 代理商： | MPC8569CVTANKGA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
DDR2 and DDR3 SDRAM Controller
MPC8569E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 0
Freescale Semiconductor
45
2.3.2
Real Time Clock Timing
The real time clock timing (RTC) input is sampled by the core complex bus clock (CCB_clk). The output of the sampling latch
is then used as an input to the counters of the PIC and the time base unit of the e500; there is no need for jitter specification.
The minimum pulse width of the RTC signal must be greater than 2x the period of the CCB_clk. That is, minimum clock high
time is 2
× tCCB_clk, and minimum clock low time is 2 × tCCB_clk. There is no minimum RTC frequency; RTC may be grounded
if not needed.
2.3.3
Gigabit Ethernet Reference Clock Timing
The following table provides the gigabit Ethernet reference clock (TX_CLK) AC timing specifications.
2.3.4
Other Input Clocks
A description of the overall clocking of this device is available in the MPC8569E PowerQUICC III Integrated Host Processor
Family Reference Manual in the form of a clock subsystem block diagram. For information about the input clock requirements
of other functional blocks such as SerDes, Ethernet Management, eSDHC, and Enhanced Local Bus see the specific interface
section.
2.4
DDR2 and DDR3 SDRAM Controller
This section describes the DC and AC electrical specifications for the DDR2 and DDR3 SDRAM controller interface of the
MPC8569E. Note that the required GVDD(typ) is 1.8 V for DDR2 SDRAM and GVDD(typ) is 1.5 V for DDR3 SDRAM.
Table 12. TX_CLK3,4 AC Timing Specifications
At recommended operating conditions with LVDD = 2.5 V ± 125 mV / 3.3 V ± 165 mV.
Parameter/Condition
Symbol
Min
Typical
Max
Unit
Notes
TX_CLK frequency
tG125
—125
—
MHz
—
TX_CLK cycle time
tG125
—8
—
ns
—
TX_CLK rise and fall time
LVDD = 2.5 V
LVDD = 3.3 V
tG125R/tG125F
——
0.75
1.0
ns
1, 5
TX_CLK duty cycle
GMII, TBI
1000Base-T for RGMII, RTBI
tG125H/tG125
45
47
—
55
53
%2, 5
TX_CLK jitter
—
± 150
ps
2, 5
Notes:
1. Rise and fall times for TX_CLK are measured from 0.5 and 2.0 V for LVDD = 2.5 V, and from 0.6 and 2.7 V for LVDD =3.3 V.
2. TX_CLK is used to generate the GTX clock for the UEC transmitter with 2% degradation. The TX_CLK duty cycle can be
loosened from 47%/53% as long as the PHY device can tolerate the duty cycle generated by the UEC GTX_CLK. See
Section 2.6.3.7, “RGMII and RTBI AC Timing Specifications,” for duty cycle for 10Base-T and 100Base-T reference clock.
3. Gigabit transmit 125-MHz source. This signal must be generated externally with a crystal or oscillator, or is sometimes
provided by the PHY. TX_CLK is a 125-MHz input into the UCC Ethernet Controller and is used to generate all 125-MHz
related signals and clocks in the following modes: GMII, TBI, RTBI, RGMII.
4. For GMII and TBI modes, TX_CLK is provided to UCC1 through QE_PC[8:11,14,15] (CLK9-12,15,16) and to UCC2 through
QE_PC[2,3,6,7,15:17](CLK3,4,7,8,16:18). For RGMII and RTBI modes, TX_CLK is provided to UCC1 and UCC3 through
QE_PC11(CLK12) and to UCC2 and UCC4 through QE_PC16 (CLK17).
5. System/board must be designed to ensure the input requirement to the device is achieved. Proper device operation is
guaranteed for inputs meeting this requirement by design, simulation, characterization, or functional testing
相關PDF資料 |
PDF描述 |
|---|---|
| MPC8569VTANKGB | RISC PROCESSOR, PBGA783 |
| MPC8569EVTAUNLB | RISC PROCESSOR, PBGA783 |
| MPC8569ECVTANKGB | RISC PROCESSOR, PBGA783 |
| MPC8569ECVTANKG | RISC PROCESSOR, PBGA783 |
| MPC8569VTAUNLA | RISC PROCESSOR, PBGA783 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC8569CVTANKGB | 功能描述:數字信號處理器和控制器 - DSP, DSC 8569 XT 800/600/400 r2.1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| MPC8569CVTAQLJB | 功能描述:數字信號處理器和控制器 - DSP, DSC 8569 XT 1067/667/533 r2.1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| MPC8569ECVTANKGB | 功能描述:數字信號處理器和控制器 - DSP, DSC 8569E XT 800/600/400 r2.1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| MPC8569ECVTAQLJB | 功能描述:數字信號處理器和控制器 - DSP, DSC 8569E XT1067/667/533 r2.1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| MPC8569E-MDS-PB | 功能描述:開發板和工具包 - 其他處理器 MPC8569 MDS PROCESSOR BD RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。