- 您現在的位置：買賣IC網 > PDF目錄367700 > P60ARM-IG (Zarlink Semiconductor Inc.) Low power, general purpose 32-bit RISC microprocessor PDF資料下載
參數資料
| 型號： | P60ARM-IG |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | Low power, general purpose 32-bit RISC microprocessor |
| 中文描述： | 低功耗，通用32位RISC微處理器 |
| 文件頁數： | 41/120頁 |
| 文件大?。?/td> | 1275K |
| 代理商： | P60ARM-IG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
Instruction Set - LDR, STR
37
4.7.1 Offsets and auto-indexing
The offset from the base may be either a 12 bit unsigned binary immediate value in the instruction, or a
second register (possibly shifted in some way). The offset may be added to (U=1) or subtracted from (U=0)
the base register Rn. The offset modification may be performed either before (pre-indexed, P=1) or after
(post-indexed, P=0) the base is used as the transfer address.
The W bit gives optional auto increment and decrement addressing modes. The modified base value may
be written back into the base (W=1), or the old base value may be kept (W=0). In the case of post-indexed
addressing, the write back bit is redundant and is always set to zero, since the old base value can be retained
by setting the offset to zero. Therefore post-indexed data transfers always write back the modified base. The
only use of the W bit in a post-indexed data transfer is in privileged mode code, where setting the W bit
forces non-privileged mode for the transfer, allowing the operating system to generate a user address in a
system where the memory management hardware makes suitable use of this hardware.
4.7.2 Shifted register offset
The 8 shift control bits are described in the data processing instructions section. However, the register
specified shift amounts are not available in this instruction class. See
4.4.2 Shifts
.
4.7.3 Bytes and words
This instruction class may be used to transfer a byte (B=1) or a word (B=0) between an ARM60 register and
memory.
The action of LDR(B) and STR(B) instructions is influenced by the
BIGEND
control signal. The two possible
configurations are described below.
Little Endian Configuration
A byte load (LDRB) expects the data on data bus inputs 7 through 0 if the supplied address is on a word
boundary, on data bus inputs 15 through 8 if it is a word address plus one byte, and so on. The selected byte
is placed in the bottom 8 bits of the destination register, and the remaining bits of the register are filled with
zeros.
A byte store (STRB) repeats the bottom 8 bits of the source register four times across data bus outputs 31
through 0. The external memory system should activate the appropriate byte subsystem to store the data.
A word load (LDR) will normally use a word aligned address. However, an address offset from a word
boundary will cause the data to be rotated into the register so that the addressed byte occupies bits 0 to 7.
This means that half-words accessed at offsets 0 and 2 from the word boundary will be correctly loaded into
bits 0 through 15 of the register. Two shift operations are then required to clear or to sign extend the upper
16 bits.
A word store (STR) should generate a word aligned address. The word presented to the data bus is not
affected if the address is not word aligned. That is, bit 31 of the register being stored always appears on data
bus output 31.
相關PDF資料 |
PDF描述 |
|---|---|
| P60ARM-B | Low power, general purpose 32-bit RISC microprocessor |
| P60A | 60W DC-DC Converter P60A-Series |
| P60A12D05P | 60W DC-DC Converter P60A-Series |
| P60A12D12P | 60W DC-DC Converter P60A-Series |
| P60A12D15P | 60W DC-DC Converter P60A-Series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P-60AS/A18 | 功能描述:BATTERY NICAD 2/3A 600MAH W/TAB RoHS:否 類別:電池產品 >> 電池，充電式（蓄電池） 系列:- MSDS 材料安全數據表:Nickel Metal Hydride Battery MSDS 標準包裝:1,000 系列:TWICELL 電池化學:鎳金屬氫化物 電池大小:AAA 電壓 - 額定:1.2V 容量:930mAh 尺寸/尺寸:- 端接類型:焊片 放電速率:186mA 標準充電電流:100mA 標準充電時間:16小時 重量:0.029 磅（13.15g） 裝運信息:- 其它名稱:SY153T |
| P60AS302 | 制造商:APEM 功能描述: |
| P60AS632-8C | 制造商:NYLOK 功能描述: |
| P60AS701 | 功能描述:旋鈕開關 10POS BCD 0.15A 24V RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
| P60AS701TR | 功能描述:旋鈕開關 10POS 0.15A 24VDC RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
發布緊急采購，3分鐘左右您將得到回復。