- 您現在的位置：買賣IC網 > PDF目錄3775 > PCA9698DGG,512 (NXP Semiconductors)IC I/O EXPANDER I2C 40B 56TSSOP PDF資料下載
參數資料
| 型號： | PCA9698DGG,512 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 29/48頁 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 40B 56TSSOP |
| 產品培訓模塊： | I²C Bus Fundamentals |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 35 |
| 接口： | I²C |
| 輸入/輸出數： | 40 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 1MHz |
| 電源電壓： | 2.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-TFSOP（0.240"，6.10mm 寬） |
| 供應商設備封裝： | 56-TSSOP |
| 包裝： | 管件 |
| 包括： | POR |
| 產品目錄頁面： | 826 (CN2011-ZH PDF) |
| 其它名稱： | 568-3241-5 935278614512 PCA9698DGG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
35
7810C–AVR–10/12
Atmel ATmega328P [Preliminary]
To avoid unintentional changes of clock frequency, a special write procedure must befollowed to
change the CLKPS bits:
1.
Write the Clock Prescaler Change Enable (CLKPCE) bit to one and all other bitsin
CLKPR to zero.
2.
Within four cycles, write the desired value to CLKPS while writing a zero to CLKPCE.
Interrupts must be disabled when changing prescaler setting to make sure the write procedure is
not interrupted.
8.12
Register Description
8.12.1
OSCCAL – Oscillator Calibration Register
Bits 7..0 – CAL7..0: Oscillator Calibration Value
The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to
remove process variations from the oscillator frequency. A pre-programmed calibration value is
automatically written to this register during chip reset, giving the Factory calibrated frequency as
specified in Table 28-1 on page 307. The application software can write this register to change
the oscillator frequency. The oscillator can be calibrated to frequencies as specified in Table
28-1 on page 307. Calibration outside that range is not guaranteed.
Note that this oscillator is used to time EEPROM and Flash write accesses, and these write
times will be affected accordingly. If the EEPROM or Flash are written, do not calibrate to more
than 8.8 MHz. Otherwise, the EEPROM or Flash write may fail.
The CAL7 bit determines the range of operation for the oscillator. Setting this bit to 0 gives the
lowest frequency range, setting this bit to 1 gives the highest frequency range. The two fre-
quency ranges are overlapping, in other words a setting of OSCCAL = 0x7F gives a higher
frequency than OSCCAL = 0x80.
The CAL6..0 bits are used to tune the frequency within the selected range. A setting of 0x00
gives the lowest frequency in that range, and a setting of 0x7F gives the highest frequency in the
range.
8.12.2
CLKPR – Clock Prescale Register
Bit 7 – CLKPCE: Clock Prescaler Change Enable
The CLKPCE bit must be written to logic one to enable change of the CLKPS bits. The CLKPCE
bit is only updated when the other bits in CLKPR are simultaneously written to zero. CLKPCE is
cleared by hardware four cycles after it is written or when CLKPS bits are written. Rewriting the
CLKPCE bit within this time-out period does neither extend the time-out period, nor clear the
CLKPCE bit.
Bit
7
65
43
21
0
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
OSCCAL
Read/Write
R/W
Initial Value
Device Specific Calibration Value
Bit
7
6
5
4
3210
CLKPCE
–
CLKPS3
CLKPS2
CLKPS1
CLKPS0
CLKPR
Read/Write
R/W
R
R/W
Initial Value
0
See Bit Description
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9506DGG,512 | IC I/O EXPANDER I2C 40B 56TSSOP |
| PCA9505DGG,112 | IC I/O EXPANDER I2C 40B 56TSSOP |
| ATTINY13-20MUR | IC MCU AVR 1K FLASH 10MHZ 20MLF |
| 5-530520-1 | CONT.HIGH CURRENT L.P. |
| 5-583875-6 | TWIN LEAF CONTACT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9698DGGS911,51 | 功能描述:I2C 接口集成電路 40-bit Fm I2C Bus I/O port w/Reset RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| PCA9698DGGT | 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 56-Pin TSSOP T/R |
| PCA9698DGG-T | 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 56-Pin TSSOP T/R |
| PCA96PWS911,118 | 功能描述:接口-I/O擴展器 8-BIT I2C FM QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9701D | 功能描述:寄存器 16BIT SPI 18V GPI INT -40 +125 RoHS:否 制造商:NXP Semiconductors 邏輯類型:CMOS 邏輯系列:HC 電路數量:1 最大時鐘頻率:36 MHz 傳播延遲時間: 高電平輸出電流:- 7.8 mA 低電平輸出電流:7.8 mA 電源電壓-最大:6 V 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-38 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。