參數資料
型號: PSD813F3V
英文描述: 60V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a UB Surface Mount package; Similar to IRHLUB7970Z4 with optional Total Dose Rating of 300kRads
中文描述: Flash在系統編程(ISP)外設的8位微控制器
文件頁數: 51/103頁
文件大?。?/td> 1185K
代理商: PSD813F3V
51/103
PSD81XFX, PSD83XF2, PSD85XF2
Table 21. I/O Port Latched Address Output Assignments
Note: 1. N/A = Not Applicable.
Address In Mode
For MCUs that have more than 16 address sig-
nals, the higher addresses can be connected to
Port A, B, C, and D. The address input can be
latched in the Input Macrocell (IMC) by Address
Strobe (ALE/AS, PD0). Any input that is included
in the DPLD equations for the SRAM, or primary or
secondary Flash memory is considered to be an
address input.
Data Port Mode
Port A can be used as a data bus port for a MCU
with a non-multiplexed address/data bus. The
Data Port is connected to the data bus of the MCU.
The general I/O functions are disabled in Port A if
the port is configured as a Data Port.
Peripheral I/O Mode
Peripheral I/O mode can be used to interface with
external peripherals. In this mode, all of Port A
serves as a tri-state, bi-directional data buffer for
the MCU. Peripheral I/O Mode is enabled by set-
ting Bit 7 of the VM Register to a 1. Figure 24
shows how Port A acts as a bi-directional buffer for
the MCU data bus if Peripheral I/O Mode is en-
abled. An equation for PSEL0 and/or PSEL1 must
be written in PSDabel. The buffer is tri-stated
when PSEL0 or PSEL1 is not active.
JTAG In-System Programming (ISP)
Port C is JTAG compliant, and can be used for In-
System Programming (ISP). You can multiplex
JTAG operations with other functions on Port C
because In-System Programming (ISP) is not per-
formed in normal Operating mode. For more infor-
mation on the JTAG Port, see the section entitled
“PROGRAMMING IN-CIRCUIT USING THE
JTAG SERIAL INTERFACE”, on page 65.
Figure 24. Peripheral I/O Mode
MCU
Port A (PA3-PA0)
Port A (PA7-PA4)
Port B (PB3-PB0)
Port B (PB7-PB4)
8051XA (8-Bit)
N/A
1
Address a7-a4
Address a11-a8
N/A
80C251
(Page Mode)
N/A
N/A
Address a11-a8
Address a15-a12
All Other
8-Bit Multiplexed
Address a3-a0
Address a7-a4
Address a3-a0
Address a7-a4
8-Bit
Non-Multiplexed Bus
N/A
N/A
Address a3-a0
Address a7-a4
RD
PSEL0
PSEL1
PSEL
VM REGISTER BIT 7
WR
PA0-PA7
D0-D7
DATA BUS
AI02886
相關PDF資料
PDF描述
PSD813F4V -200V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-2 package; A IRHNA597260 with Standard Packaging
PSD813F5V -60V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-2 package; Similar to IRHNA9064 with optional Total Dose Rating of 300kRads
PSD86 THREE PHASE RECTIFIER BRIDGE
PSF101 WORLD MAGNETICS ULTRA SENSITIVEPRESSURESWITCHES
PSG61 4 KEY BI-BI CALL
相關代理商/技術參數
參數描述
PSD813F3V-12 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F3V-12J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F3V-12JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F3V-12JIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F3V-12JT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs